0
If this is the 3.0 V6 engine (Saab) the coolant thermostat is located between the cylinder heads on the passenger side of the engine. The upper radiator hose connects to a split pipe that uses an O ring to seal the two segments.
To get to the thermostat you must remove the intake manifold assembly, then remove a base plate below that. Prior to removing the top aluminum housing from the thermostat use a large wrench and separate the aluminum pipe leading from the top radiator hose to the theromostat into two sections. Place the wrench on the end where the upper radiator hose connects, and after removing the small bolt that holds the front pipe segment secure, twist the outer pipe out of the flange of the inner pipe. Then remove the two bolts holding the cover and inner pipe over the thermostat and remove the inner pipe and old thermostat. clean the area, replace with new thermostat and cover. An updated kit is available from Saturn with new thermostat, gasket, cover, and O ring.
What else can I help you with?
How do you change the thermostat on a 2000 Chevy Lumina?
do i need to change the manifold when replacing thermostat
How do you change thermostat on 2000 Toyota MR2 Spyder?
To change the thermostat on a 2000 Toyota MR2 Spyder, start by draining the coolant from the radiator. Next, remove the engine cover and disconnect the hoses attached to the thermostat housing. Unscrew the thermostat housing, replace the old thermostat with a new one, and reassemble everything in reverse order. Finally, refill the coolant and check for any leaks.
Where is the thermostat on a 3.5 L 2000 Dodge?
It should be on the drivers side of the engine. Follow the lower radiator hose to the engine, that is where the thermostat housing is at. That is how it is on the 2000 300M.
How do you change the thermostat on a 2000 Honda Passport?
To change the thermostat on a 2000 Honda Passport, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant and remove the upper radiator hose from the thermostat housing. Unbolt the thermostat housing, remove the old thermostat, and clean the mating surfaces. Install the new thermostat with the correct orientation, reattach the housing, hose, and refill the coolant, then reconnect the battery.
Where is thermostat located on 2000 Chevy Blazer?
Follow the upper radiator hose back to the engine, it is connected to the thermostat housing on the engine. The thermostat is located under the thermostat housing.
How do you change thermostat in 2000 Chrysler cirrus 2.4?
To change the thermostat in a 2000 Chrysler Cirrus with a 2.4L engine, first ensure the engine is cool, then disconnect the negative battery cable. Drain the coolant from the radiator, and remove the upper radiator hose connected to the thermostat housing. Unbolt the thermostat housing, replace the old thermostat with a new one, ensure the gasket is in place, and reassemble all components. Finally, refill the coolant, reconnect the battery, and check for leaks.
How do you change the thermostat on a 2000 Cadillac Escalade?
To change the thermostat on a 2000 Cadillac Escalade, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator, then remove the hoses connected to the thermostat housing. Unscrew the thermostat housing, take out the old thermostat, and replace it with a new one, ensuring the gasket is in place. Reassemble everything, refill the coolant, and reconnect the battery.
How do you change the thermostat in a grand voyager?
where is thermostat in 2000 chrysler grand voyager ??
What is check engine code P1126 2000 Nissan?
Engine thermostat malfunction
Engine runs hot how can you tell if its a water pump?
my engine runs hot on my 2000 dodge caravan how can i tell if its the water pump i already change the thermostat does not help
Where is the thermostat on a 2000 Chevy Mailbu?
Where the upper radiator hose connects to the engine you will find the thermostat.
How do you change your thermostat in a 2000 Ford Mustang?
To change the thermostat in a 2000 Ford Mustang, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator, then remove the upper radiator hose from the thermostat housing. Unscrew the thermostat housing, replace the old thermostat with a new one, ensuring the gasket is in place, and reassemble everything by reversing the steps. Finally, refill the coolant and check for leaks.
