0
How do you clean and load a Connecticut valley 50 cal muzzle loader?
Wiki User
∙ 13y ago
This requires a MUCH longer answer than we can give on WikiAnswers. Lucky for you, there is a book on this subject- called the owner's manual. Follow the link below, select your rifle, click on it, and you will have the manual. Strongly suggest you print it, and READ THE ENTIRE MANUAL before you do anything with the rifle. NEVER use anything but black powder, or a BP subsitute such as Pyrodex in your rifle, and NEVER fire it when the bullet is not snugly on top of the powder charge. Good luck, shoot safe, wear your eye protection. If, after reading the manual, you still have questions, you can contact me through my message board.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How can i remove breach plug from mossberg 50 cal muzzle loader barrel?
If you are talking about the 50 caliber muzzle loader barrel for the Mossberg 12 gauge Shotgun model 500 or the Maverick 88 - you can't remove the breech plug. You have to clean the barrel like a flintlock. I just bought one from Mossberg's web page (arrived yesterday 12/21/08). It didn't come with any instructions. Fortunately, I found the manuals online at the following addresses: Muzzle Loader Barrel http://www.mossbergs.com/manuals/Muzzleloader.pdf 12 Gauge Shotgun Model 500 http://pdf.textfiles.com/manuals/FIREARMS/mossberg_500.pdf Good Luck
How do you clean the ak47?
using the cleaning rod (which is located under the muzzle) and other applienses
How much does it cost to dry clean a sweater?
In Connecticut its about 6.50
How do you clean a 30-30 Marlin Model 200-h lever action from the muzzle end?
It's always best to clean from the breech end, but if you want to clean from the muzzle end, simply open the bolt, and then run your cleaning rod down the muzzle. Might be a good idea to put a piece of old rag in the bolt opening so the debis that is pushed out, wont end up in the action. Marlins are very easy to clean from the breech end. Simply open the lever half way, pull the lever screw, remove the lever, then pull the breechbolt out. You can now clean from the breech end.
Why were the cities in the indus valley so clean?
The cities in the Indus Valley were very clean because of the meticulous way they were built in. The city's sanitation and waste water technologies had substantially developed.
Does pool daddy clean pools in the west valley?
Pool Daddy doesn't service the far west valley, but our services do extend as far as Glendale and Peoria.
When cleaning a firearm what end of the firearm should you generally clean from?
When possible, clean from the chamber to the muzzle. Due to the design of some firearms, this may be difficult or impossible. Cleaning in that fashion will push fouling/ carbon OUT of the gun, away from the working parts.
How do I get to Ojai Valley Inn?
The best way is via Country Club Drive. If you are traveling south on this road, the Ojai Valley Inn will be on your right. There is a nice clean entrance there for you to take.
What are the Credit Valley wolves?
The Credit Valley Wolves are hockey team. the people that play for them are a bunch of dusty mcduster pants. They are dusters of the world. Even the swiffer cannot clean these dusters.
Why was Mesopotamia's river valley important?
Because the people had clean water, a good place to grow crops, and if they had boats they had transportation.
Can the muzzle break on a weatherby v 30-06 be removed?
Assuming the gun is a Weatherby Mark-V then probably. Weatherby's Accubrake is typically threaded on the gun, and it is not a bad idea to unscrew the muzzlebrake ever so often and clean the threads. However, it is not uncommon to use bonding agents such a locktite in place to keep the muzzle-brake from unscrewing itself under the force of recoil. Depending on the bonding agent use this can make un-screwing the muzzle brake range from difficult to pipe-dream. It is also important to note that muzzle-brakes do more than just reduce recoil. Once a gun has been threaded for a muzzle-brake, said brake also pulls double duty helping to protect the crown of the barrel and has an effect on the barrel's rigidity. If you remove your muzzle-brake you should probably put it back, or replace it with a thread protector before firing the gun. If you firearm is not a standard Mark-V Weatherby, or you cannot unscrew your muzzle-brake you should have a gunsmith take a look at the gun for you.
What is the value of 50 cal hawken model 5024 made in mid 80s?
I PAID $300 FOR MINE LAST YEAR ,AN OLDER RIFLE BUT VERY CLEAN. 50 CAL MUZZLE OADER, PERCUSSION CAP.
