0
How do you clean the speed sensor or connector on a 98 Nissan Frontier?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How can you clean the Idle Air Control Valve on a 1998 Nissan Frontier?
how can I clean the Idle Air Control Valve on a 1998 Nissan Frontier
What is making your Clio not start after short journeys?
Faulty TDC Sensor, All it will need is cleaning. Take it out clean the tip of the sensor so it is clean and shiny again, also clean the electrical connector.
If ABS light goes on and having error discontinuity on rear right sensor do you have to check the cable of the sensor or do you have to replace it?
You have to find the problem and fix it. If it's a connector, repair or clean the connector. If it's the sensor, replace the sensor. There are no "one size fit's all" repair answers.
How do you clean Mass air flow sensor on a 1998 Nissan Altima?
how do you clean mass air flow sensor on a 1998 Nissan altima? To clean the mass air flow sensor , you need to get a can of CRC mass air flow cleaener frm auto zone, Kragen, Pepboys, Sensor is attached to the tube (next to airfilter). again you need to use mass air flow cleaner ( CRC ). I use this on my ford windstar and Nissan sentra 05 and 95. it runs better after cleaning the mass air flow sensor.
What might cause and how might you fix the speedometer on your 1992 4Runner which works sporadically and sometimes not at all?
I suspect that you have a bad contact on your speed sensor connector in your transmission. Check connector underneath the car on the driver side, if connector is clean you might need to replace the sensor ( electrical pulse generator ) that's where you plug in the connector...
How much 134a freon do you need for a 2002 Nissan frontier 4x4 if added to much how to remove it?
The air conditioning system capacity of the 2002 Nissan Frontier is 25 ounces of R134A type refrigerant. The Clean Air Act of 1990 requires the refrigerant to be removed by a certified technician.
How do you replace a throttle sensor in a 1988 Nissan Sentra?
Is it easy to replace a throttle body in an 88 sentra? How do you clean a throttle body
How do you change a speed sensor on a 95 Ford Aerostar?
Removal: 1. Disconnect the negative battery cable. 2. Detach the speed sensor connector at the rear differential. 3. Remove the sensor hold down bolt, then remove the sensor. 4. Clean the axle mounting surface using care not to get any dirt in the axle housing. 5. Inspect and clean the magnetized sensor pole piece. To install: 6. Lubricate the new o ring on the sensor with new motor oil, then install the sensor. 7. Tighten the retaining bolt to 30 ft. pounds (40Nm). 8. Reattach the wiring harness connector. Connect negative battery cable.
1989 Nissan 240sx start up revs up high then dies?
When i had this prblem it was my mass air flow sensor check the wiring and clean the sensor its an expensive part if its bad put simple to replace
I have a 91 Chevy pickup that runs for 15 min then dies has new coil ignitio module and pickup coil?
I had the same problem bud. Remove and inspect the crankshaft sensor. Also clean the connector pigtail inside with a spray for electronic contacts. Inspect the connector pins of the pigtail closely for damage. Get your sensor at Oreillys NOT autozone.
How do you replace camshaft position sensor on a 1997 Mercury Sable 3.0 engine twelve valve?
Replacing the Sensor1. Disconnect the negative battery cable...just like on every other installation 2. Detach the CMP sensor connector next. 3. Remove the CMP sensor retaining bolt and remove the CMP sensor Now to install: 1. Clean the CMP sensor surface and ensure that the O-Ring is in place. 2. Position the CMP sensor into the engine and tighten the retaining bolt to 71-106 inch lbs. 3. Attach the CMP sensor connector 4.Connect the negative battery cable.
Can you clean an oxygen sensor on a dodge 5.9 360 magnum?
You can not successfully clean an oxygen sensor. You need to replace it.
