0
A 3way switch at each location is what you use, but it must be wired properly to work. You must have incoming power at one switch location and no power at the other location. The other location has the wire going up to the light. You then need a 3 conducted wire such as 12/3 or 14/3 running between the switches. Use the same size wire you used to power the switch and top up to the light. You then connect the black power wire at one location to the black screw on the switch, and at the other location you connect the black wire going to the light to the black screw on that switch. At each location tie the whites together under a wire nut and shove that back in the box. Tie the grounds together and connect that to the ground screw at each switch. At each location you will now have the black and red wire from the wire you ran between the switches left. Those are called travelers. Connect those wires to the remaining 2 screws left on the switches at each location. Does not mater which you connect to which screw. Assuming no other wires are involved this is how you wire it.
Wiki User
∙ 11y ago
Wiki User
∙ 10y agoOn one end of the 3/way circuit is the power coming to the switch. On the other end of the 3/way circuit is the wires going to the light. Just connect that wire to the 1st light and then go from there to the next light.
Add your answer:
Earn +20 pts
Is there a way to wire a 3 way household dimmer switch as a 2 way dimmer switch?
You need a three way switch to control lights from two locations. The name is misleading. Three way switch refers to the connection points on the switch. You can use a three way switch as a single switch as long as you place hot wire on the brass screw and the use any of the other screws for the return hot.
How do you control 4 light in one switch and the same lights control by 4 switches?
You want four switches to independently turn 4 lights on and off. You need two 3-way switches, and two 4-way switches. The first 3-way is located where the power first comes into this system, two travelers (wires) go to the first 4-way switch, two travelers then go from that switch to the other 4-way switch and two wires go to the final 3 way switch. The third wire on the last 3 way switch then goes to the first light fixture. This is a complicated wiring project and it is not as simple as it sounds. Realistically, you will have more than 2 wires traveling between switches depending on whether the neutral is located, and further more dependent on whether power from the panel first comes to a switch or to a light fixture. You need to plan this well or you may have more wires in one or more boxes than code allows. Also, wires must be attached in particular positions on all the switches, or you will end up with a situation where some of the switches will work and some won't and troubleshooting is very complex.
How did a 'three-way switch' get its name?
"How does a single pole switch differ from a three way?" is a trick question often asked to catch-out new trainee electricians because the common but mis-named "three-way switch" is actually a single pole, double throw switch, i.e. it is only a 2-way switch, not a 3-way switch.A pair of "3-terminal, single pole, double throw" switches are often used to hook-up two separate light switches to control one light or one set of lights.A proper "3-way switch" would be capable of being switched to 3 different positions and could have one, two or more poles. Each pole could be either single- or double-throw.The same answer put in a different wayDespite the fact that the name "3-way switch" is often used to describe it, if it is of the type that has just one pole that can only be physically switched 2 ways, the name "3-way switch" is quite wrong for that particular switch. A "3-terminal, single pole, double throw" switch" is a more accurate description for it.Comment'Three-way switch' -American term. 'Two-way switch' -UK term for the same type of switch. Used to operate a lamp from two different locations.
What is a two way lever switch?
In electrical terminology it is known as a single pole double throw switch.
How do you install a dimmer switch for multi fixtures where the original switch has 2 black wires and one red with no green?
This simple if you have two switches controlling a set of light you will need to buy a three way switch. A three way switch will have a place for three connection. Depending on what brand of switch you purchase the directions will be sightly different but most dimmer come with detailed directions and diagrams. When you by a dimmer you need to read what kind of load it is meant to control. They are built to control incandescent light, magnet low voltage lights or electronic lights.
Where can a circuit with two lamps with single pole switch fluorescent lamp with two 2 way and an intermediate control can be used?
This type of circuit would never be used. The two way fluorescent system would depend on the voltage being supplied by the two lamp circuit switch. If the switch turns off the two lamp circuit the rest of the circuit with the fluorescent fixture would become inoperable.
What type of switch is installed to control a luminaire from two different control points?
A Three-way switch. 3-ways are used to control from two locations. As opposed to a Four-way switch, which is needed to control from more than two locations.
What is three way switching?
A three way switch is use control in two station of the lamp
Where is switch for reversing lights on a 99 ranger?
On the drivers side of the trans case, mid way twords the top. It's a screw-in switch with a two wire connector- one to the fuse the other to the lamps.
What are the disadvantages of a two way switch?
What is Disadvantages of two way switch
How can an intermediate switch be used with a 2-way switch system to control a light from four floors?
A two way switch is UK terminology for a North American three way switch. Though the switch has two names it is still a Single Pole Double Throw switch that has three terminals. North American terminology. The circuit is the same as the three way switch system. To control from four locations just add another intermediate switch. For the system to work properly the new intermediate switch has to be adjacent to the existing intermediate switch. The connections must run - three way, intermediate, intermediate, three way.
Is there a way to wire a 3 way household dimmer switch as a 2 way dimmer switch?
You need a three way switch to control lights from two locations. The name is misleading. Three way switch refers to the connection points on the switch. You can use a three way switch as a single switch as long as you place hot wire on the brass screw and the use any of the other screws for the return hot.
When installing lights with 2-way and intermediate switching control the intermediate switch must be connected to the?
to wire a lamp to be controlled from three places you need two three way switches and one four way switch. the two traveller wires that would normally run between the two three way switches must be connected to the terminals of the four way switch
The way the break is used to take control out of switch is same as continue to take control of the beginning of the switch?
yes
Does brake switch control cruise control?
On most vehicle the brake switch is one way to shut the cruise off.
Would a dash dimmer switch be ok to use to dim front fog lamps?
No, way way to much load, may cause a fire!
Which logic gate is similar to two way switch?
XOR gate is a two way switch...beacuse connection is on when two variables are different
