answersLogoWhite

0

What else can I help you with?

Continue Learning about Electrical Engineering

You have just replaced your ceiling light and when you turned the power back on the light stays on even when you turn off the switch?

Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.


How do you wire a circuit so that the switch only controls the second receptacle and the first receptacle is always energized?

You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.


Why won't my Light turn off at switch?

Presuming the switch worked at one point and just stopped working it is likely that the switch has failed in a normally closed position. The only other possibility is that somehow you have a wire problem whereby the hot side of supply is connected to the load side of the switch. This could be caused by an exposed wire in the switch receptacle. Suggest you turn off power at breaker and replace switch as a start. When you have the switch removed from the receptacle, with wires still connected see if switch works. If it does it could still be bad, but examine the wires around switch and see if you have any exposed wire that could be touching the load side of the switch (Side connected to the light).


How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?

If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.


How do you wire a light to a switch at the end of a run and which controls an outlet?

Bring power into the light switch box 12/2 or 14/2 wire depending on the existing wire. Make sure you use the exactly same size wire that is used on that circuit. If you do not know look at the breaker in the main panel that controls power to that circuit. 20 amp will be 12/2 wire and 15 amp will be 14/2 wire. Now run another wire from the switch box out to the outlet. Inside the switch box, strip both white wires back 3/4" and connect them together under a wire nut and push this back into the box. Connect the 2 ground wires together and then connect that to the ground screw on the switch. You now have 2 black wires left. Connect them to the 2 screws on the light switch. Does not matter which black wire you connect to which screw. At the outlet connect the ground wire to the green ground screw, black wire to copper screw, and white wire to silver screw. That outlet will now be controlled by the light switch.

Related Questions

How do you wire a receptacle to a switch?

To wire a receptacle to a switch, you need to connect the hot wire from the power source to the switch, then connect another wire from the switch to the receptacle. Make sure to turn off the power before starting and follow proper wiring diagrams to ensure safety and functionality.


How do you wire a receptacle from two switches one is 3 way one is single pole?

You cannot wire a single pole switch and 3 way switch together.


How do you wire a switch to a light?

To wire a switch to a light, you connect the hot wire from the power source to one terminal on the switch, then connect another wire from the other terminal of the switch to the hot terminal on the light fixture. Finally, connect the neutral wires from the power source and the light fixture together.


Can you wire a light switch with only one 14-2 wire?

If the power feed goes directly to a fixture, or if you are wishing to switch a receptacle that is not now switched, you can us a 14-2 NM cable to install a "switch loop", provided the circuit is no larger than 15 amps. To do this, after running the 14-2 NM cable, connect the WHITE conductor of the 14-2 to the hot wire. At the switch, connect the black and white conductors to the switch terminals. At the fixture or receptacle, the black wire of the 14-2 NM cable now becomes your switch leg and is connected to the black conductor of the fixture or brass terminal of the receptacle. The NEC (for the United States) requires that the switch be fed with the white wire and the black wire be used as your switch leg.


How can I connect a wire switch to a light fixture?

To connect a wire switch to a light fixture, first turn off the power to the circuit. Then, connect the black wire from the switch to the black wire from the light fixture using a wire connector. Next, connect the white wires together and the ground wires together. Finally, secure all connections with electrical tape and mount the switch and light fixture as needed.


How do I wire a fan and light switch together?

To wire a fan and light switch together, you will need to connect the hot wire from the power source to the hot terminal on the switch. Then, connect the hot wire from the fan to the other terminal on the switch. Finally, connect the neutral wires from the power source, fan, and light together. Make sure to follow all safety precautions and consult a professional if needed.


You have just replaced your ceiling light and when you turned the power back on the light stays on even when you turn off the switch?

Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.


How do you wire a circuit so that the switch only controls the second receptacle and the first receptacle is always energized?

You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.


How do you run a light with a switch from a existing outlet with out controlling the out let with the switch?

Break off the tab that jumps between the wire mounting screws on the side of the receptacle. This turns one receptacle into 2 seperately controlled parts--one is always hot and the other is controlled by the switch (the one with the lamp plugged in).


How do you wire a light switch and outlet together?

To wire a light switch and outlet together, you will need to connect the hot wire from the outlet to the hot terminal on the switch. Then, connect the neutral wire from the outlet to the neutral terminal on the switch. Finally, connect the ground wires from both the outlet and switch to the ground terminal on the switch. Make sure to turn off the power before starting and follow all safety precautions.


How do I wire a light switch to a light?

To wire a light switch to a light, first turn off the power to the circuit. Connect the black wire from the switch to the black wire from the light. Connect the white wire from the switch to the white wire from the light. Finally, connect the ground wire from the switch to the ground wire from the light. Secure all connections with wire nuts and cover with electrical tape. Turn the power back on and test the switch to ensure it is working properly.


How do you wire two electrical recepticles in one box?

A switched duplex receptacle can be wired two ways. If both duplexes are to be switched then the receptacle is wired the same as any light fixture. The black wire from the bottom of the existing switch goes to the brass screw on the receptacle that is to be switched. The white wire terminates on the neutral silver coloured screw. If you want just half of the duplex receptacle to be switched then the tie bar between the two brass screws on the receptacle has to be removed. Just wiggle it until it breaks free. Usually on a half switched receptacle the top half is switched and the bottom half remains a normal connection. After removing the tie bar, the top half of the receptacle is wired the same, as the description above, for a full duplex switched receptacle. Questions use the discuss question page.