0
How do you correctly wire a switch to a bathroom fan light combo you have 1 w b g coming from your breaker box you also have 2 w b g wires one that controls the fan and one that controls the light?
Flashover600
Tie all White wires together.
Tie the Grounds together and connect them to the ground screw on two switches.
Create a pigtail with TWO black wires coming out.
Connect a black wire to each of the two switches. (you pick which screw, but be consistent.
Connect the black wire from the light to the remaining screw on one of the switches.
Connect the black wire from the fan to the remaining screw on the OTHER switch.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is the difference between a run and a circuit?
run in a electrical system means a wiring & conduit runs coming from Panel Board Circuit Breaker to its branch circuit loads in a circuit. while circuit is a designated number of branch breaker in a panel board where power load was individual connected.
Why would you have 252 volts coming out of a 240 volt breaker?
simple what goes in comes out mains has a % mark of around 10% under or over so that's not un normal to see this info
Where do I ground if there is No ground coming out of the box?
The question doesn't say what "the box" refers-to: is it a wall box for a socket outlet or is it for a switch - or is it actually the main circuit breaker panel for the building or apartment?You can add a safety ground wire to any wall box - to connect appliances back to the ground on main breaker panel - only if there is a main grounding wire installed at your main breaker panel.You can't add a safety ground wire to any wall box, to connect appliances back to the main breaker panel, if you don't already have a ground wire installed at your main breaker panel. If that is the case, your wiring must be at least 50 years old. It is time to consult with an electrician...As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What is the difference between a differential circuit breaker and a circuit breaker?
A circuit breaker is a device that opens its contacts in order to open the circuit in case of current overload. A differential circuit breaker is a device that opens the circuit in case of leakage (current measured on the phase line is differentthan the current returned to neutral line); therefore protects users from electric shocks.To more understand how it operates, consider the following:Say that your electrical wall outlet is connected to a differential breaker. When plugging let's say a hair dryer to it, the current traveling on the phase line (going into the hair dryer and out to the neutral line of the wall outlet) equals but in reverse direction of the current returned to the neutral line, thus the difference is zero. Now let's say this hair dryer got faulty and fraction of the current coming from the outlet phase line travels through your body and return to earth (considering that you are not electrically isolated from the ground). Thus the current in neutral line is less than the current on phase line; at this moment the difference is not zero and breaker opens to protect you from getting electrocuted.
What do you use a clamp meter for?
The clamp part is for measuring amps via induction. You set meter to amps and clamp around only a single wire. Device you are measuring must be operating. This means you couldn't clamp around a lamp cord to a table lamp since the current induced in each direction cancels out. You would have to separate the wires. An electrician would carry a short extension cord with the wires already separated. Most often a clamp meter is use to checks amps in a breaker panel on the black wire coming from the breaker.
How do we tell if the leak in the kitchen ceiling is coming from the bathroom or the roof?
If it's coming from the roof then the bathroom ceiling will have a water stain on it too. If you don't see this then it is coming from your bathroom.
One of the 120 volt legs in the main breaker has lost power?
check power coming into the breaker if both leads are hot it's a bad breaker
When coming to an RR with no controls what should you do?
Look, watch, and listen to make sure a train is not coming.
What should you do if you have a leak in your bathroom that is coming out of the wall?
You need to call a plumber.
If your European going into the bathroom what are you coming out?
Maybe Eurelieved (you're relieved).
How could the following sentence be written correctly nobody saw nothing coming?
Nobody saw anything coming.
In Bridge to Terabithia what did Jess suggest they do about the person crying in the bathroom?
Jess suggests asking the teacher to check on the person crying in the bathroom.
How siphon breaker works in the big closed tanks?
A siphon breaker works in big closed tanks by transferring fluid to an upper level coming into a tank from above. The purpose of the siphon breaker is to produce pressure at its outlet and the fluid weight to produce pressure.
What does diaphragm in a microscope do?
It controls the amount of light coming up into the objective lens.
Can your puppy get diseases going to the bathroom near others?
yes. if coming in contact with the fecies then yes.
Why do you have black gritty oily water coming from your bathroom faucet?
Your pipes aren't clean "Dah"
Which correctly explains the term brainstorming?
Brainstorming is a creative problem-solving technique where a group generates ideas and solutions through spontaneous and free-flowing discussion. It encourages participants to share their thoughts without criticism or judgment, leading to innovative and diverse solutions to a problem.
