0
simple what goes in comes out mains has a % mark of around 10% under or over so that's not un normal to see this info
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What kind of breaker would you use for a 220 hook up?
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
Can you run a 480 volt machine with 600 volt incoming voltage?
Yes, but the 600 volts would have to be transformed down to 480 volts. Direct connection to the motor with 600 volts would overheat the motor to destruction.
How can you determine if you have 110 or 220 volts?
Most residential service in USA has both. In the USA 110 to 120 volts is a given and it would be very unusual not to have 220 to 240 volts. It can be easily tested at main panel with a volt meter. Or as an alternative call your power company.
How many volts are 16milli - volts?
0.016 volt
How do you wire a 277 to 120 volt transformer?
The voltage 277 volts is a three phase line to neutral voltage of a 480 volt system. What is needed for the protection of the transformer is a two pole breaker from the 480 volt CDP (Central Distribution Panel). The breaker will be sized to the KVA of the transformer. The wire will be sized to the breaker plus 25%. The electrical code requires that on motor and transformer feeders, they be sized to 125% of the total current capacity of the equipment.
How many volts can you draw off of a 15amp breaker?
It's the amps that are controlled by the breaker not the volts. You can have a 600 volt 15 amp breaker, you can have a 347 volt 15 amp breaker. The breaker will trip when you exceed 15 AMPS.
How many volts can b drawn off a 240 volt breaker?
240 volts maximum.
What kind of breaker would you use for a 220 hook up?
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
How can I get 230 volt single pole wire from my house panel?
In North America you can not obtain 230 volts from just one single pole breaker. The distribution is like this, from a one pole breaker to neutral is 120 volts. From an adjacent breaker to neutral is 120 volts. From the adjacent breaker to adjacent breaker (breakers situated beside each other) the voltage will be 230 volts.If you want to incorporate a 120 to 230 volt transformer into the circuit you can obtain 230 volts. The primary side of the transformer will be connected to the 120 volt circuit and the secondary side of the transformer will output 230 volts. The transformer must be sized to the load amperage or the load wattage of the connected 230 volt load.
How volts comes from a 20amps breaker?
On most residential circuit breaker boxes in North America, each individual breaker represents one 120-volt circuit. Two breakers ganged together represent a 240-volt circuit.
Would a 15 kva 380 volt generator be big enough to run a house with a 60 amp breaker 380 volts?
A 15 KVA - Generator operating at 380 Volts can cater to only 22.79 Amps. It cannot cater to a 60 Amps breaker
What circuit breaker to install for 10 amp 250 volt circuit?
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
Is there a difference between 480volt 30 amp breaker and 208volt 30 amp breaker?
Yes, all breakers have an insulation factor as to the maximum amount of voltage the device can be subjected to. A 208 volt breaker has a maximum up to and including 240 volts. A 480 volt breaker has a maximum up to and including 600 volts. A higher voltage rating breaker can be used on lower voltages but not the other way around.
One of the 120 volt legs in the main breaker has lost power?
check power coming into the breaker if both leads are hot it's a bad breaker
Can you use 240 volts with a 120 volt supply?
Only if the cable going to your well pump is a three wire. The third wire could carry the neutral and you will have 120 volts from either 240 leg to the neutral.
How do you switch from 120 volt to 240 volt in house?
Answer for USA, Canada and countries running a 60 Hz supply service.To operate a 240 volt load in the home you use two adjacent breakers. This will give you a voltage of 240 volts where as one breaker to neutral will give you 120 volts.
What unit would be used to measure the potential difference between two poles of a battery?
The volt.The volt.The volt.The volt.
