0
Use a sawzaw with a metal cutting blade
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What do you do if your car muffler is falling off?
Go to a muffler shop and have it welded back on or replaced
How do you take off a rear side quarter panel on a 2001 Oldsmobile alero?
Cut it off, it is welded on.Cut it off, it is welded on.
On a 98 Honda civic is the muffler bolt on or is it welded on?
yes at the cat then oem muffler welded on..... so u plan on doin a catback??
How do you change a cadillatic converter on a Oldsmobile alero?
you will have to buy a new one and cut off old one and have some one weld it back on if there is no bolt that hold it on most have to be cut and welded back on you might have to got to a muffler shop to have it instaled
How do you bolt on the muffler to a 1999 Chevy Malibu?
Well if it is bolted, you simply unbolt the old one and bolt in the new one. If not, the old unit it must be cut or torched off and the new one welded in its place. Usually done at an exhaust shop, will cost about $100 if you bring them the muffler.
What will happen if you cut your exhaust pipe off but leave the muffler on?
If you were to cut off your exhaust pipe the muffler would come off with it, sence it is attached to the very end... I would be alot louder, it might hurt your MPG rating....
How do you install a catalytic converter on a 2000 Dodge Grand Caravan?
It's welded in like a muffler. Any muffler shop can do it for you.
How to change a muffler on Chevy S-10?
First off, crawl under the truck and see if your present muffler is welded on or clamped on. If it's welded on you will need to get an exhaust cutting tool from like Autozone and cut the old muffler off BUT before you do, get your new muffler and measure how far the inlet neck is and outlet neck is on the new muffler and this will tell you how far to cut. You could hold the new muffler up to the exhasut and mark how far from the muffler you need to cut. This is assumign you are replacing the bad muffler with a new one of the same size. Now there is an inlet pipe and and out let pipe on the muffler. You will also need to have the right size clamps. Pu tone clamp on the exhaust pipe going to the engine, then push the exhaust pipe into the inlet end of the muffler and slide the clamp down and snug it up but do not tighten it. Put the other clamp on the exhaust pipe towrd the rear of the truck, push the exhasut ipe into the outlet end of the muffler and then slide the clamp down onto the joint and snug up. if everythign aligns right, then tighten the clamps. Sometimes if you overtighten the clamps you will have exhaust leaks. If you cannot get the joints to seal, you may need to get your system welded. If you exhaust is leak free then you are done. After a few hot and cold cycles you may just want to crawl back under and check the bolts on the clamps just in case they came loose from the heat and cold cycles.
Does your car need a cut out muffler?
Muffler cut out? Not needed in most states illegal
Will a bad muffler cause your car to start up then cut off if put in different gear?
NO!
Where are the catalytic converters?
if your car has duel exhaust, they should be located a foot or two away from the headers, since the exhaust heat makes them work. They have to be cut off by a mechanic, and new ones welded back on as well. They should be closer to the engine then the muffler, around the transmission in an impala. hope this helps
How do you installed muffler for Mazda MX6 LS?
take it in and have one welded on cant beat the sound and quality....
