0
The design of a Screw Clamp was done in the following steps: Step 1: All the components of a screw clamp assembly under consideration were sketched and labeled separately. The parameters, to be determined analytically, were identified (on the sketches). Dimensions which were found empirically were also identified (on the sketches). Parameters and dimensions including: the screw end angle, the relationship of the set screw, lubricating ducts, plugs and pad dimensions to screw diameter, were estimated empirically. Step 2: The loads on the screw, nut, frame, clamping pad and handle were estimated, as and when each part was designed, one after the other. The service life of each part was visualized. Step 3: The requirements and desired outputs of the screw clamp and each of its parts were projected, as each part was designed, one after the other. Step 4: Materials and processes were chosen tentatively for each part, as and when each part was designed, one after the other. Reasons for each choice were recorded as shown below. Step 5: To quantify the dimensions, design quantities for each part were recorded as shown below. The distortion energy theory was used to determine several sections of the frame on the basis of bending. All dimensions, materials and processes were finalized and shown on the supplied drawing. A bill of materials was also made. The efficiency of the screw was estimated, and included in the specifications of the screw.
Wiki User
∙ 11y ago
Wiki User
∙ 9y agoA C clamp is called that because they are in the shape of the letter C. These clamps are used to hold wood or metal pieces together while working with them.
Add your answer:
Earn +20 pts
How do you design a computer using c plus plus?
C++ is used to write programs, not to design computers. If you want to design computers, use a CAD program specifically intended to aid in electronics design.
C program on left factoring in compiler design?
how to create a c program for left factoring.
What would your role be in the design and development of the system conversion to C in your current work?
Going through the existing system & code and coming out with design.
What tools are used in design technology?
Buffer coping saw file g clamp hammer maker steel rule saw try square wet dry board hope this helps xx
Why high bred inheritance not use in C sharp?
It was the designer's decision. One would have asked the similar question if it had been design the other way. It would not be fun with another hybrid, in inheritance design, language just like C++.
What is an c-clamp?
a clamp in the shape of a c where you tighten it by twisting the end.
What is c bar clamps?
A C-clamp is a clamp that is in the shape of a "C" that screws down to hold pieces together. A Bar-Clamp is a long clamp made from a bar or steel rod that has grips on each end that can be adjusted along the bar and engages ratchets and then can be screwed down to tighten. So a long clamp with C shape end clamps coule be called a C-bar clamp.
What are the example of clamping and holding tools?
bench voice, voice grip, g clamp, c clamp, hand clamp, jumper cable. these are only hand tools
How do you retract brake pistons on golf car?
You can either use a c clamp or c clamp vise grips hope this helpa
When Changing the brakes on a 2005 Outback do you use a C Clamp or do you have to screw the calipers back?
you can use the c clamp just tighten it slowly
What type of a simple machine is a clamp?
A C-clamp contains a screw, a lever, and a wheel and axle.
What is a c-clamp?
A C-clamp is a tool, essentially it is a C-shaped piece of metal with one flat surface and a threaded rod with a "foot" and handle on opposite ends. Turning the threaded rod in a clockwise direction closes the C and forms a clamp. See the link below for an image.
How do you use a C clamp to compress the piston?
You dont compress a piston with a C clamp, you use a piston ring compressor to compress the rings and tap the top with a hammer to sit it back in to the cylinder bore. The C clamp is used for compressing valve springs. *AArOn*
What is the size of a C clamp based on?
the size of the object. there are diffrent sizes of c clamps
How do you compress the brake caliper on a 1995 Ford Taurus?
A C-clamp, open the clamp wide enough to put it over the piston (round metal thing) then close the C-clamp until it is pushed back far enough to allow brake pads to fit properly. Remove the clamp and your golden
How do you compress the break caliper?
I use a c-clamp and one of the old break shoes. Put the old shoe against the caliper and use the c-clamp to push it back in.
What to do to keep your bike seat from moving?
Disassemble, clean and reassemble the clamp. Tighten harder. If this fails, get another clamp, or another seat post, depending on the design.
