0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When was Smax created?
Smax was created in 2000.
What is a unique name for a solid white cat?
Puff, magic, smax. x
What metal is the ford smax made of?
Aluminum shell so rather heavy.
How do I convert short circuit current to fault level. I have a 110kV grid which has a maximum short ccircuit current of 30kA?
It is very simple. Use the following equation: Smax=sqrt(3)*V(line-line)*Isc(max) for your case: Smax=5715.76 MVA
How do you disable the alarm on a 2007 Ford S Max?
I don't think you can! I have the same model and year and my alarm module decided to go haywire last week in the dead of night, it was going off every 30 seconds but there were no flashing indicator lights. It was so frustrating. I searched on the SMAX Owners club people on there suggested pulling fuse F26 from the main fuse board under the glove box but then later reported it still went off because the module has a battery back up installed that is designed to power the alarm if the battery lead is cut so even disconnecting the battery may not stop it going off. The alarm is configured in such a way as you can only select via the settings menu to change the protection level as you exit the car and lock it. As soon as you lock the car the alarm is activated. I tried in vain to stop it going off using these settings, made no difference. You could have the alarm de-installed but it could have implications on the ECU software and could require a re-program. I thinks alarms are a waste of time and pain when the go wrong, no one ever takes notice of them, I even ignored mine last week to start with as I didn't even think it was mine going off. If someone wants to steal from the car or the car itself no alarm will protect against the most determined thieves.
Why won't my keyfob open the doors on my smax?
Most common causes - Keyfob battery needs replacing, or keyfob electronics have been damaged by immersion in water or excessive heat.
What has the author Mary Heidi Zimmerman-Linville written?
Mary Heidi Zimmerman-Linville has written: 'VOb2 smax prediction by submaximal bicycle test and the twelve-minute run test in high school population' -- subject(s): Oxygen in the body, Testing, Respiration, Exercise tests, Physical fitness
How do you change front fog lamp not bulb on ford smax?
Remove the two torque type mounting screws from the headlamp and gently move the headlamp out of the way, Power cable to headlamp can be removed but not needed. Easy access to fog lamp bulb is then achieved. Disconnect fog lamp power cable and twist bulb to remove.
How do you Change brake light bulb s max?
Assuming this a Ford Smax you are talking about - I struggled for a while - until it became clear. Here is my posting from the fordownersclub.com.Replacing the lower brake light bulb on a Ford Smax is far easier than on first inspection. As the owners manual states both panel covers beside the brake light need to be removed but what the manual doesn't tell you is that a grey plastic foam panel behind the larger panel must also be removed (careful as it is easy to tare). This comes out easily as there no clips etc holding it in. Now two white plastic wing nuts should be visible both behind the small panel. The first wing nut is accessed via the small panel opening, and the second wing nut is accessed via the much large opening once the large plastic foam panel is removed. The wing nuts once unscrewed come away (i.e. do not stay in place) so be careful you don't lose them into the interior of the wing. The whole lamp must now be removed. This is very easily achieved by gently pushing on the wing nut screws you have just exposed. Once the lamp unit is free on the exterior, the short electric cable to it, needs to be disconnected by pressing on the top release. To expose the bulbs, the single screw on the bulb holder needs to be removed. The brake bulb is a 380 12V 21/5W. Price €3.70 for a pair in Halfords. Take care not to touch the bulb when inserting. Follow these instructions in reverse order to replace the unit.The original answer is below.Normally you need to remove the tailight housing to gain access. Usually there are screws that can be accessed from the outside. Once you do this you may need to turn the "bulb holder" while pushing in. This should release the bulb holder from the tailight housing. Then you may need to do the same thing to get the bulb out and replaced. Then reverse the process for installation.If you want to change the central brake light the user manual says use a screwdriver to release the clips, this is incorrect. Having just changed the bulb on my wife's S-Max I can advise that the stainless steel clips need to be pinched together using your fingers and the whole lens assembly including the clips pushes out through the body of tailgate. Good luck!Read more: How_do_you_replace_the_tailgate_brake_light_in_a_ford_s_max
A ball is thrown horizontally from a cliff at a speed of 15 ms and strikes the ground 45 meters from the base of the cliff How high was the cliff?
KE before collision =1/2 m v2 = 1/2 m (15)2= 1/2 m 225 (Velocity)2 after collision v2=u2 +2as Final velocity is 0 when object is at maximum height u is the initial velocity just after the rebound a is due to gravity = -9.8ms-2 s is the displacement = 5m 0 = u2 + 2(-9.8)5 u2=98 (ms-1)2 KE after rebound = 1/2 m 98 since mass does not change Fraction of KE remaining = 98/225 Fraction lost 1 - fraction remaining 1- (98/225) = 127/225 Not: if g is taken to be 10ms-2, then fraction is 125/225 = 4/9
