answersLogoWhite

0


Best Answer
Copy

take it to your gm dealer it was a recall

User Avatar

Wiki User

โˆ™ 2015-07-15 20:05:26
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you fix a 1997 GMC truck windshield wiper motor?
Write your answer...
Submit

Related Questions

How do you remove the windshield wiper motor on a 1997 Nissan Maxima?

* Remove the windshield wiper arms * Remove the cowl cover * Disconnect the electrical connectorr from the wiper motor * Detach the wiper motor/linkage assembly from the cowl * Remove the wiper motor retaining bolts and remove the motor


Where is wiper motor on a 1997 Dodge Caravan?

It is under the cowl below the windshield


Where is the windshield wiper washer motor on a 1997 Oldsmobile cutlass?

Check either at the bottom of the windshield washer fluid reservoir or check to see if the wiper motor has washer hoses connected to it


Where is the front windshield wiper motor located in a 1997 Plymouth voyager?

Under the black cowling at the base of the windshield.


Does one motor control both windshield wiper blades on a 1997 Nissan Sentra?

YES


What are the dip switch settings on a 1997 sunfire windshield wiper motor?

Please clarify or explain what you are trying to accomplish. There are no dip switch setting on that wiper motor that I have ever seen.


How do you locate the windshield wiper motor on a 1997 jeep wrangler?

You get to drop you windshield...the wiper motor is under it. Unbolt the rollbars at the top of the windshield, then unbolt both brackets on each side of the dash. Carefully fold the windshield down on the hood. Then you'll see your wiper motor. I just did this yesterday on my 95 YJ. Try putting some PB Blaster/WD40 on all the bolts and letting it soak in. I had to make a trip to Fastenal for a few replacements.


Where is the windshield wiper fluid reservoir on a 1997 Chevrolet Monte Carlo?

The 1997 Chevrolet Monte Carlo windshield wiper fluid reservoir can be found in the engine compartment. The windshield wiper fluid reservoir will be on the drivers side of the engine compartment.


How do you change the wiper motor on a 1997 Jeep Cherokee?

I changed the wiper motor in my 95 JGC. remove the vent near the windshield on the exterior of the jeep... you will have to open the hood. remove weather stripping and about 5 screws to remove the plastic vent, and the wipers. the wiper motor is located on the drivers side near the windshield below the vent. a couple bolts to take out, pull the wiper motor out of the rotating arms, unplug, and replace.


Where is the windshield wiper motor on a 1997 Chevy Camaro?

it should be behind the cowel on the drivers side above the master brake cylinder.


Installing windshield wiper motor for a 1989 ford expidition?

Ford Expeditions where built from 1997 & UP... Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ONposition. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


Where to get windshield wiper wiring diagram for a Dodge Ram 1500 pickup.?

Do u have a wiper motor wiring digram for 1997 doge ram 1500 pickup 2 wheeldrive


How do you remove a front wiper motor on a 1997 expedition?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


How do you replace rear wiper motor 1997 Ford Explorer?

how do you replace rear wiper motor on a 1997 ford explorer


How do you remove a 1997 Ford Expedition winshield wiper transmission there doesnt seem to be clearance to get it out.?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


How do you change wiper motor in 1997 Chevy truck?

You must first remove the wiper arms. then, remove the screws holding the black plastic grill under the wiper arms. This will expose the motor. You will then need to disconnect the wiper arm transmission linkage from the motor, the remove the three bolts holding the motor on. Install in reverse order.


Where is the wiper motor on a 1997 Pontiac Grand Prix?

The motor is under the plastic grill that is at the bottom of the windshield. It's held in place by a bunch of plastic "rivits" that you have to remove to get the grill out.


How do you prevent the windshield wipers from running regardless of the wiper switch position on a 1997 Toyota 4Runner?

unplug the wiper motor under your hook, its located at the back of the engine compartment on the passenger side


Where does the windshield wiper fluid go in a 1997 Eagle Talon?

i dont know....MAYBE WHERE THE WINDSHIELD WIPER FILLER CAP IS...ITS WHITE SO YOU NOTICE IT!!!


How do you change wiper blade on 1997 dodge ram truck?

The 1997 Dodge Ram Series Pickup takes 20" replacement windshield wiper blades on both sides front. For installation, the replacement wiper blades will come with simple-to-follow, step-by-step, illustrated instructions


How do you install wiper motor for BMW 740il?

wiper motor not working on my 1997 BMW 740IL


What is wrong if the windshield wipers don't work in your 1997 Ford Ranger Pickup extended cab?

Either the fuse is blown or the wiper motor is bad.


How do you replace the wiper motor on a 1997 Chevrolet C1500 pickup?

Remove the wiring harness from the wiper motor. Remove the wiper arm linkage. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.


How do you install wiper motor on 1997 z71?

Remove the vent panel located at the base of the windshield. Locate the motor. Replace. Be sure and realign the wipers to specification ... or else, one or both would be offline.


Wipers stopped on 1997 S-10 truck Fuse is good No previous history Is it the motor?

The pulse board may be at fault. We have a large fleet of Chevys and every time we have a wiper problem it is never the wiper motor, it is the pulse board which is attached to the wiper motor. This part is available at your local auto parts store. It can be changed easily without removing the wiper motor from the vehicle.