answersLogoWhite

0


Best Answer

you just need to hone it out and replace parts with rebuild kit.

User Avatar

Wiki User

โˆ™ 2006-03-19 19:32:13
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you fix a slave cylinder in a 1993 ford ranger?
Write your answer...
Submit
Related questions

Where is the slave cylinder on a 1997 Ford Ranger xlt?

The slave cylinder for a hydraulic clutch on a Ford Ranger is inside the manual transmission bellhousing


How do i repair the slave cylinder on my 1988 Ford Ranger?

The slave cylinder on a 1988 Ranger can not be repaired. The cylinder will have to be replaced, then the system bled.


Where is the clutch slave cylinder on a 1993 ford ranger 4x4?

I believe that is inside the manual transmission bell housing


Where is the the bleed valve on a slave cylinder on a 1993 ford ranger?

The bleed valve is located on the drivers side of the bell housing.


How do you change the slave cylinder on a 2002 Ford Ranger?

the slave cylander is located in the transmission on the 2002 Ford Ranger. Better see a mechanic to do the job.


Where is the slave cylinder on a 88 ford ranger?

The slave cylinder for a hydraulic clutch is located inside the manual transmission bellhousing


Where is a slave cylinder on a 95 ford ranger?

The slave cylinder for a hydraulic clutch is inside the manual transmission bell housing


Where is the clutch slave cylinder found on a 1995 Ford ranger xlt?

The slave cylinder for your hydraulic clutch is inside the transmission bellhousing


Location of clutch slave cylinder of 1994 ford ranger?

The hydraulic clutch slave cylinder is inside the manual transmission bellhousing


Where is the clutch slave cylinder on a 1997 ford ranger?

The clutch slave cylinder for a hydraulic clutch is inside the manual transmission bellhousing


Where is the slave cylinder located on a 1997 ford ranger xlt?

The slave cylinder for your hydraulic clutch is located inside the transmission bell housing


Does the slave cylinder on a 2001 ford ranger compress in or screw in?

If you are talking about the line it compresses in.


Does the transmission of a 1994 ford ranger 2.3l have to be removed to replace the slave cylinder?

yes


What fluid goes into the slave cylinder?

On a Ford Ranger , DOT ( 3 ) brake fluid


How much does a 1993 Ford Ranger 4-cylinder gas tank hold in gallons?

I have a '93 Ford Explorer and it hold 19 gallons From the Chilton Ford Ranger guide: "1993 Ranger with standard wheelbase: 16.3 1993 Ranger with long wheelbase: 19.6"


Does a 1993 2.3 Ford Ranger have a non-interference engine?

Yes , the 2.3 liter 4 cylinder in a 1993 Ford Ranger is a non-interference engine


Is the clutch in the 1993 ford ranger a hydraulic clutch?

yes it is with the slave cylinder being inside the bee housing. the clutch master cylinder reservior is to the right facing the firewall. it requires brake fluid


How does a holes come off a 1993 ford ranger slave cylinder?

You drive the cold roll pin out, BUT if planning on replacing slave cyl, replacing the master line and slave as a unit is recommended more often then not there will be a leak when replacing line.


How do I attach the cable from master cylinder to the slave cylinder in a 1993 Ford Ranger?

the master and slave cylinder are a built in unit,there is no cable between them. there are piston'fluid connected. you can buy a rebuild kit for $9.00. But it is much better to buy a rebuilt master cylinder than try to rebuild it. Especially on ABS master cyclinders.


What connects slave cylinder to clutch pedal on 1987 ford ranger?

The clutch pedal assembly has a clutch rod that pushes in on a clutch master cylinder. There is a hydro line that goes from the master cylinder to the slave cylinder.


Can you use a transmission from a 1993 Ford Ranger to a 2000 ranger?

can you use a transmission from a 1993 ford ranger in a 2000 ford ranger?


Where is the slave cylinder in a 1985 Ford Ranger extended cab truck?

The slave cylinder for the hydraulic clutch on a manual transmission is located inside the manual transmission bell housing


Where is the clutch slave cylinder on a 2004 Ford Ranger 2.3 liter?

It is located inside the bell housing.


What size motor is in a 93 Ford Ranger xlt four cylinder two wheel drive five speed?

The 4 cylinder in a 1993 Ford Ranger is 2.3 liter ( 140 cubic inches )


Is the slave cylinder on the inside or outside of the transmission of a Ford Ranger 2002?

The slave cylinder is INSIDE the transmission bellhousing , it slides over the transmission input shaft , and then is bolted to the transmission. To change the slave cylinder the transmission has to be removed , but the slave cylinder line can be blead from the bleeder outside of the transmission bellhousing