answersLogoWhite
Ford Ranger
Ford Expedition XLT
Ford Ranger XLT

How do you fix the engine surge in your v6 1984 Ford Ranger 4x4?

394041

Top Answer
User Avatar
Wiki User
Answered 2006-06-23 08:29:30

Check your vacuum lines this usually the cause for a surge in engine speed when idling or running.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


Mazda used the ford ranger body but used the Mazda engine.


( .044 inch ) for your 2.8 liter V6 engine in your 1984 Ford Ranger , according to motorcraft . com


If you are debating on whether or not you want to buy a Ford Ranger, then it is useful to know the engine size. The Ford Ranger is available, with a V6 engine.


The Ford Ranger engine number can be found on the engine identification plate. The engine identification plate can be found on the engine block.


No , the 2.3 liter 4 cylinder engine in a 1997 Ford Ranger is not an interference engine


No , the 2.5 liter - 4 cylinder engine in a 1998 Ford Ranger IS NOT an interference engine


who made the 1995 2.3 litre engine in the ford ranger?


If you're talking about the 4.0 L V6 ( NO ) The 2000 Ford Ranger 4.0 L was the OHV and the 2004 Ford Ranger uses the 4.0 L - SOHC - engine


Yes, they should swap out. As long as the cab style is the same, then the 1983-1987 Ford ranger doors will fit a 1984 Ranger.


The ignition timing on the 1984 Ford Ranger is : 2.0 L - 4 cylinder - ( 8 degrees BTDC ) 2.3 L - 4 cylinder engine - ( 6 degrees BTDC ) 2.8 L - V6 engine - ( 10 degrees BTDC ) unless engine compartment sticker shows different


Take your 2002 Ford Ranger to the garage to get the engine checked.


There is supposed to be an engine thermostat . Do you mean that someone has removed the engine thermostat ? What year of Ford Ranger and what year ?


What year of Ford Ranger , and what engine size ?


On a 1984 Ford Ranger , 2.8 liter V6 engine : The marked # 1 position on the distributor cap faces towards the REAR / passenger side Starting at the # 1 position , go CLOCKWISE > , ( 1 - 4 - 2 - 5 - 3 - 6 ) The engine cylinder locations are numbered : firewall 3 - 6 2 - 5 1 - 4 front of Ford Ranger ( V6 engine )


No. From 1983-84 Ford used the C3 transmission. A 1990 will not fit.


are there freexe out pluges on rear of block on a 2.3 engine ford ranger


The 3.0 L - Vulcan engine - was one of the engines offered in a 1995 Ford Ranger


How do you set the timing on an 1988 ford ranger 4 cylinder


According to Gates ( they manufacture timing belts ) the 2.3 L engine in a 1994 Ford Ranger is NOT an interference engine


On a Ford Ranger , 3.0 liter V6 engine : The engine oil filter is on the drivers side of the engine


where is the number 3 cylinder located on a 2.5 ford ranger engine


That would depend on what year of Ford Ranger and what size of engine it has


1984 schematic refers to either your engine electrical wiring { picture of the wiring} or diagram like where vacuum hoses run to . your answer is a Chilton's manual or a Haynes manual.


The 2004 Ford Ranger starter is located on the right hand side of the engine. The starter will be at the back of the engine.


Only if you have the 2.5 liter four cylinder engine in a 2001 Ford Ranger . ( that engine has a timing BELT )



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.