answersLogoWhite
Nissan Frontier
Radio

How do you fix the radio display light on a 2001 Nissan Quest or how does the radio get the power for the LED display?

575859

Top Answer

User Avatar
Wiki User
2007-08-23 12:53:03
2007-08-23 12:53:03

Go to www.shareamemory.com/radio for $19.99 they provide directions. Go here for a free step by step instructions free: http://forums.vmag.com/mvquest1199/messages/363.html For free instructions, go here... http://www.ford-trucks.com/forums/112400-radio-display.html To recap: 1. Pull out drink holder out and remove two screws. 2. Pry the console out from the top, no need to completely remove. 3. Remove four screws holding the radio. 4. Disconnect 3 wire harnesses and antenna to remove radio. 5. Open radio face plate. 6. Open the top cover of radio. 7. Remove small circuit board inside radio to the left by bending 2 twisted tabs and remove one screw. 7. On bottom of circuit board, look for surface mount components R1057/C1071/R1058/C1083/R1064. 8. Resolder with small tip soldering iron. I resoldered all the joints while I was at it, just to be sure. Total time from getting the tools from the toolbox and clean everything up was less than 1 hour. Good Luck!! Some cases, you will need to replace the board of the CD/cass unit. This is due to a component in the LCD being fried, which can be seen by removing it from the system including the metal plate covering it. The component is in the lower-right corner (facing the display), and is locked within the LCD glass.

12

Related Questions

User Avatar

omo drenarlevel aire al sistema del power steering de Nissan Quest 1998?

User Avatar

The 2013 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)1 one-touch power windows wide.

User Avatar

The 2001 Nissan Quest is 6 ft. 2.9 in. (74.9 in.)12V front power outlet(s) wide.

User Avatar

The 2002 Nissan Quest is 6 ft. 2.9 in. (74.9 in.)1 one-touch power windows wide.

User Avatar

The 2014 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)1 one-touch power windows wide.

User Avatar

The 2011 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)1 one-touch power windows wide.

User Avatar

The 2012 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)1 one-touch power windows wide.

User Avatar

The 2008 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)12V front, 12V rear and 12V cargo area power outlet(s) wide.

User Avatar

The 2005 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)12V front, 12V rear and 12V cargo area power outlet(s) wide.

User Avatar

The 2006 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)12V front, 12V rear and 12V cargo area power outlet(s) wide.

User Avatar

The 2004 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)12V front, 12V rear and 12V cargo area power outlet(s) wide.

User Avatar

The 2007 Nissan Quest is 6 ft. 5.6 in. (77.6 in.)12V front, 12V rear and 12V cargo area power outlet(s) wide.

User Avatar

power is coming display is not coming

User Avatar

Disconnect the fuse that goes to the horn but also that fuse may power something else also. Mr brown

User Avatar

Some advantages of a liquid-crystal display are that it is light, compact, has no geometric distortion, used minimal power, thin, has little flicker, and more.

User Avatar

Do you have power to the connection that is on the back of the center brake light? the red wire should have voltage to it. If not, it may be grounding out somewhere.

User Avatar

http://www.courtesyparts.com/ that link is to a Nissan site where you can select your car (year and model) and then go through their diagram driven catalog. the switches are typically listed under "door trim" and is also called a "finisher" (as in, the finishing piece) specifically for the 1999 quest: http://www.courtesyparts.com/betasite/quest-v41-1998-2002/genuine-nissan-parts/bodyside-rear/809-front-door-trimming/-c-5063_5064_5191_5201.html

User Avatar

how to remove a power steering pulley on a 1997 Nissan altima

User Avatar

where is the power steering pump on a nissan vanette 2000 2.3 d

User Avatar

If the power source is capable of delivering the additional power required, then the original two light bulbs display no change in their voltage, current, or power dissipation when more light bulbs are added in parallel with them. So the only effect of having added more is that there are then more glowing light bulbs, and there is then more light in the laboratory.

User Avatar

Liquid-crystal display televisions (lcd), Use a lot of Power. Light-emitting diode (led) is using Half the power. So buy led tv!

User Avatar

my 1996 Nissan pick up doesn't have horse power

User Avatar

LCD stands for Liquid Crystal Display in which each segment that turns on actually turns black when electricty is applied to that segment. When the power is applied to it the liquid polarizes lining up the molecules and actually blocking the light going through it which is why you would need a light source behind it to see it operate. When the power is turned off to that segment the liquid unpolarizes and lets light through and has the illusion of disappearing. On the other hand the bar graph display operates on a different principle by using LEDS (Light Emitting Diodes) which may be arranged as a row of rectangles is actually a type of semiconductor similar to a transistor. When power is applied to a LED the phosphor in the substrate gives off light. An LCD display can also be shown as a bar graph but each segment will appear black as each segment is activated.

User Avatar

If the display is not on when you turn the ignition on. First you check the fuses. radio memory is usually run with the courtesy light fuse. The main radio fuse is marked radio. Second you pull the radio out and test the power leads to the radio. If you have no power then there may be a short in a wire. If there is power on the power leads then the radio must be replaced.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.