answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2011-09-13 02:15:28

i have no clue i have the same problem with my Mazda 1999 626

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


It is located right behind the ignition. It is important that this part is working correctly so that your car will start.


There are a few reasons why a 1994 Mazda Protege won't start, but does crank. A couple of reasons could be the air flow sensor or a problem in the fuel lines.


The cost to replace a 1999 Mazda Protege serpentine belt will vary depending on the cost of parts and cost of labor. The prices for the serpentine belt start at $14.56.


3.5 0r 3.7 qts i would start with 3.5


battery may be dying and altenater may be going out


Do you really expect people to tell you how to steal a car? If it's your car, use the key.


car stalled at red light and will not start. there is no spark from spark plug, help!


The ignition timing can be adjusted. Attach the timing light to the battery and connect it to the cylinder. Loosen the distributor adjustment bolt and start the engine. Remove the vacuum hose from the carburetor. Read the timing and make the necessary adjustments.



plenty of things could be a starter, alternator, ignition switch, bad spark...


Just push it a few feet with the ignition switch turned on and pop the clutch.


I would check the ignition coil , and ignition module(which is only replaced with the whole distributor assembly).You can also check the ohms in the crank sensor(the wire is found over by the timing belt cover)and the crank sensor gap(which is at the crankshaft )very seldom a ecm go's bad.Sometimes a simple doing plugs and wires will become the fix.


Check battery Check battery cables for corrosion or looseness Check fusable link


if it just goes click click click and not start then you will require a new battery or a charge if you left the lights on...


My 2002 GMC Envoy won't start,no lights come on when trying to jump start the battery. And my key won't remove from the ignition. What's should i do?


The best way to start approaching the diagnostics of the problem is to isolate possibilities. Start by testing the fuse to ensure you don't have a bad fuse.



You need to turn the ignition to the on or start position, and then push the retaining pin to remove the cylinder. If you can not turn it, then you can either drill it out, or call a locksmith to come asist you.


Flooded in the river or flooded by gas? Any "check engine lights"? Full gas pedal depression is the normal way to clear gas flooding or first remove the spark plugs and blow out the excess gas.


needs a coil or distributor it could also be that the alternator isn't working and the car may be draining the battery every time you drive it



I had same problem, turned out to be an oxygen sensor i think.... tried new ignition cables and coils first, helped but didn't solve it....


I replaced it on my 2000 protege, and it was attached to the fuel pump inside the gas tank, and it is right under the back seat. if yours is the same, you will need to turn on the car unplug the pump relay that will turn off the car, unplug your battery, and start from there


i have a 2003 Pontiac grand am, no start, does not even turn over. could it be the ignition switch?


If your 1988 Chevy Corsica key only turns in the ignition and does not start the automobile, it is probably unfixable. Remove the ignition switch retaining ring. Slide the out and remove the wiring harness. Reverse the process to install the new ignition switch.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.