0
How do you get all of the light switches to be in the down position for off when you have more than one switch for them?
Wiki User
∙ 15y ago
Three way switches do not have a up-on down-off position. With the lights off, reposition the switches so that the handles are all down. This is the start position and depending on how you enter the room and turn on the lights certain switches will be left up when you leave the room. That is just the design of the switches and for the asthetics of the look, all handles down the lights will be out.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the function of four way switch?
The use of a four way switch is needed when a load (such as a light) needs to be controlled from 3 locations or more. For instance when you walk down a hallway and there is a light there are probably at least two switches one at the beginning of the hallway and one at the end. These two switches will turn the light on or off from either location. These two switches will be three way switches. When the need to control a light or a load from more that two locations arises a four way switch is introduced. A light or load can be controlled an unlimited amount of locations by adding four way switches which are wired in between the two three way switches. Think of a sandwich where the three way switches are the bread and the meat and veggies are the four way switches. You can put as much meat and veggies as you want, but you always need two slices of bread on the top and bottom.
What must be checked when inspecting isolator enclosure?
When installing an isolator switch enclosure, make sure that the terminations are tight and secure.If you are using the isolation switch to disconnect a load that must be worked on the following should be checked. Make sure that the handle of the switch is down and locked in the off position. For isolation switches that have windows in the front of them look and make sure that the switch blades are physically in the open position. Then lock the switch in the off position. Always safety first.
How to wire single switch to operate 2 lights?
Answer for USA, Canada and countries running a 60 Hz supply service.The first thing to do at the distribution panel is to turn off the breaker feeding the receptacle's circuit.To the new two gang light switch box, two wires will go from the wall receptacle, connected black to black and white to white and ground to ground, to the new two gang light switch box and then two more sets of cable wires will leave the new light switch box and proceed up to the new individual light fixture boxes.In the two gang switch box, first connect the incoming and outgoing ground wires to the ground screw in the new switch box.Be sure to connect the ground wire around the grounding screw in the light fixture box.Next the white wires will be spliced together with a wire nut and pushed to the back of the box and then the incoming "hot" wire will be connected across the top of the two new switches.Pre position the switches in the off position, which is the handle down, before attaching the wires. The "hot" incoming wire connects to two pigtail wires coming from the top screw of the two switches. These three wires will be spliced together with a wire nut and pushed to the back of the new switch box.The two black outgoing wires that feed the new light fixture boxes are connected to the bottom screws of the individual switches.When either switch is turned to the on position, voltage will be applied to the appropriate fixture junction box.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliancesalways use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What does common mean on a light switch?
On a single pole single throw there is no common terminal. On a single pole double throw it is the terminal that is common to both the top and bottom terminals. The "hot" wire is connected to the common terminal so that when the switch is in the up position that terminal becomes energized and there will be no no voltage on the bottom terminal. When the switch is in the down position the bottom terminal becomes energized and there will be no voltage on the top terminal. In relays thisis known as a C form configuration.
How do you change a light switch the new switch is different it has terminals on same side the old one their on opposite sides?
Answer for USA, Canada and countries running a 60 Hertz supply service.Turn the breaker off to the circuit that you are working on. As long as there are only two screws on the new switch wire it the same as the old switch. Take one wire off the old switch and install it on the new switch. Then do the same thing with the last wire. On the switch you will see a dimple on the switch handle. Position it so that it faces the floor when you re install the new switch into the wall box. By doing this the switch will be in the correct position to be off when the handle is down and on when the handle is in the up position. Turn the breaker back on and you will be good to go.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you adjust the brake light switch?
Most brake light switches ratchet into position and self-adjust. To reset the adjustment, press the brake pedal part way down & pull the switch out toward the pedal until it clicks several times.
Should the light in a newly wired house be off when both 3-way switches are in the down position?
When you have two switches that control the same light(s) there are only 4 possible states. Up Up Up Down Down Up Down Down If the starting position is Down/Down and th light if OFF then Up/Down or Down/Up states will turn ON the light. If the starting position is Up/Down or Down/Up and the light is ON then Up/Up or Down/Down will turn lights OFF.
How do you wire a 2 way light switch down stairs to a 1 way switch up stairs?
You don't. You use a pair of two-way switches ('three-way switches' in US/Canada).
If a light-fan switch worked as one switch up turns on the lights and the other down turns on the fan then why would the fan switch suddenly reverse so up is on?
Sounds like someone has tinkered with 3-way switches (used to control one light from 2 switches).
Why don't 3-way and 4-way switches have on and off?
There is no designations because depending on the positions of the other switches in the circuit, the light could be on or off in either the up or down position.
What is the meaning of rocker switch?
A rocker switch is a type of switch (i.e. light) that rocks when switched, rather than trips like the majority of switches. The side of the switch not in use will be raised, while the active side will be pressed down.
2000 ford explorer the windows all go down from the drivers side but none of the others will from the other switches?
Driver's "Lock" switch broken or in locked position?
What is the function of four way switch?
The use of a four way switch is needed when a load (such as a light) needs to be controlled from 3 locations or more. For instance when you walk down a hallway and there is a light there are probably at least two switches one at the beginning of the hallway and one at the end. These two switches will turn the light on or off from either location. These two switches will be three way switches. When the need to control a light or a load from more that two locations arises a four way switch is introduced. A light or load can be controlled an unlimited amount of locations by adding four way switches which are wired in between the two three way switches. Think of a sandwich where the three way switches are the bread and the meat and veggies are the four way switches. You can put as much meat and veggies as you want, but you always need two slices of bread on the top and bottom.
Why does my automatic warehouse door go up but does not come back down?
Check for the mechanical. On the wiring site, it has different cables for up and for down, but same hardware (just switch the phase, then motor got different rotation). So if mechanical is okay, check the cables wiring
Is it possible for a power surge to trip a toggle light switch from the upright off position to the downwards on position?
No, and by the way the switch you have is in the upside down position. The light switch should be in the up position when on and in the off position when down. If the switch is that loose change it out as the internal contacts are becoming loose and soon arcing will become apparent when you use it. The other possibility is that the switch in question is part of a multi switch arrangement whereby two switches control the same light. Since you didn't mention the possibility in your question maybe someone just turned on the switch from another location. I had this similar situation recently when a home owner was experiencing strange circumstances with lights not turning off or on correctly on rare occasion. Turns out 3-way switch was wired incorrectly. If your switch truly changed positions by itself then Woodman66 is 100% correct. Just make sure you don't have a phantom problem. In another similar case a house was mis-wired and had two breakers feeding the same light. Note one way to identify a 3-way switch is that it doesn't have on or off identified on the toggle switch.
What order do you position the switches on 24 carrot island?
The two outside switches go halfway down, and the middle one all the way down.
What is the difference between toggle switch and a push button?
A toggle switch is like a light switch. You flick (or 'toggle') the switch on or off and it stays in that position until you flick it again. You could compare a push button switch to a key on a keyboard. When you press a key momentarily it will display one letter on the screen. If you hold down the key, the same letter will repeat (e.g. aaaaaaaaaaaaaaa). Toggle switches can also look like push button switches. Most power buttons on a desktop computer tower is a toggle switch. The reset button on a computer tower is a push button switch.
