Carpet glue by its nature is extremely sticky as it is made to keep a rug from moving. If you need to get the glue off of a concrete floor you can use a floor grinder. You can also scrape it.
No cracks or loose pieces, and no water problems.
Yes, if the base is stable the new layer will bond and create a new, fresh surface.An unstable base will give bad results. You should pressure wash the old concrete to get rid of loose and spalling concrete and you should use a bonding agent to serve as a primer to get the new layer to bond well to the old.Obviously, if the new concrete is laid over concrete that is subsiding because of a sinking foundation, the new concrete will crack. You need to stabilize the old concrete before pouring new over it.If you put new over old, it needs to be at least a couple inches thick else it will not cure properly. If you simply want to improve the surface, there are special self-levelling concrete mixes that can be poured thinner and still be strong. Take a look at the link below for a good how-to.
loose cargo is simply cargo that is loose
It's called bladder control. Most people get it when they get older (8 and up) and loose it when they get really old (around 80 or 90). It's very easy for most people to do when they get older.
This is a method on how to place concrete underwater, this method place a big role in offshore concreting, since cement looses its strength and fade away under water, Tremie method is to be used. Tremie Concrete is done by using a formwork/pipe which will have one end of the formwork/pipe above water and other bottom end immersed under the water and with the help of gravity.A tremie is a watertight pipe, generally 250mm in diameter, having a funnel shape hopper at its upper end and a loose plug at the bottom or discharge end. The valve at the discharge end is used to de-water the tremie and control the distribution of the concrete. The tremie is supported on a working platform above water level, and to facilitate the placing it is built up in 1 to 3.5m section.During the concreting, air and water must be exclude from the tremie by keeping the pipe full of concrete all the time; and for this reason the capacity of the hopper should be at least equal to that of the tremie pipe. In charging the tremie a plug formed of paper is first inserted into the pipe as the hopper is filled the pressure of fresh concrete forces the plug down the pipe, and the water in the tremie I displaced by concrete.For concreting, the tremie pipe is lowered into position and the discharge end is kept as deeply submerged beneath the surface of freshly placed concrete as the placed concrete as the head of concrete in tremie permits. As concreting proceeds the pipe is raised slightly and the concrete flows outwards. Care should be taken to maintain continuity of concreting without breaking the seal provided by the concrete cover over the discharge end. Should this seal is broken, the tremie should be lift and plugged before concreting is recommended. The tremie should never be moved laterally though freshly placed concrete. It should be lifted vertically above the surface of concrete and shifted to its new position.When large quantities of concrete are to be placed continuously, it is preferable to place concrete simultaneously and uniformly through a battery of tremies, rather than shift a single tremies from point to point. It has been recommended that the spacing of tremies be between 3.5 and 5m and that the end tremies should be about 2.5m from the formwork. The risk of segregation and non-uniform stiffening can be minimized by maintaining the surface of concrete in the forms as level as possible and by providing a continuous and rapid flow of concrete.How is the Underwater Concrete Mixes?For Structural concrete following must be consideredCoarse Aggregate: Gravel of 3/4" (20mm) max. size. Use 50-55 % of the total aggregate by weight.Sand, 45-50% of the total aggregate by weight.Cement: Type II ASTM (moderate heat of hydration), 600 lbs/yd3Pozzolans: ASTM 616 Type N or F, 100 lbs/ yd3Water/Cement Ratio: 0.42 (0.45 Maximum).ƒWater-Reducing Admixture (preferably it is also plasticizer): Do not use superplasticizers.ƒAir-Entrainment Admixtures: To give 6% total air.ƒRetarding Admixture: To increase setting time to 4-24 hours, as required.ƒSlump: 6 1/2" ± 1"ƒThis mix will develop compressive strength in the range of 5,600 - 7,000 psi at 28 days.
Vacumming carpet removes loose material from carpet but a carpet shampooer will clean the carpet in addition to just removing dirt. Think of brushing leaves off your shirt as opposed to washing it.
If you let the concrete dry on the ceramic, they have bonded. You can try to chisel it loose.
You need to make sure the concrete is clean and free of loose debris. Patch any holes in the concrete (let dry and settle).
No, the carpet pad moves far to much and your tile will look loose and crooked in a very short amount of time. Also, the carpet pad will not allow the adhesive to bond to it.
Only if the carpet sustained damage above the standard of normal-wear and tare. Fraying carpet, dirty spots, and loose carpet nails are all considered normal wear and tare and are exempt from damage claims.
No, they need sand. Baby and juvenile dragons should have a reptile carpet with no loose strings, or they can loose their nails. - erin_animal_lover
The loose earth has some give to it allowing the ground to absorb some of the energy from the impact. The concrete has no give and the full force is absorbed into your body.
No cracks or loose pieces, and no water problems.
Yu can get a concrete drill and crew them in.
First, remove all the possible loose brownie crumbs by vacuuming over the brownie that fell on the carpet. Then, use some really tough stain remover (like Resolve, which works the best), and spray it on the carpet. Let it soak for a minute or two, and then try scrubbing it with paper towels or something. Repeat until brownie is gone.
Nothing really happen intell you loose alot.
Steve's Carpet Services at 355 Lincoln Ave Cliffside Park, NJ can do carpet re-stretching. Call them at (201) 313-1771.