answersLogoWhite

0


Best Answer
Copy
99 sebring PS bracket boltsFrom under the car - One bolt is easy - Just behind that one ,behind the web of the bracket is another which I removed with a 3/8 drive scocketand a very short extention . Now from farther back with about a 3 foot extention and your 3/8 drive 15 MM scocket above the exhaust at about a 45 degree angle forward ,on the back of the cylinder head is another bolt with a oil line also supported by it !!! Taking the bolts out takes a bit of time and *#@*&% . Tomorrow comes the real problem !!! Getting the pump bracket and oil line bracket both in position and the bolt started with out cross threading it !!!!!!!!

Keep Smiling John S.

User Avatar

Wiki User

โˆ™ 2015-07-15 18:50:38
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you get the power steering bracket bolts out of a 1999 Chrysler Sebring Convertible?
Write your answer...
Submit

Related Questions

Front license plate mounting Chrysler Sebring convertible?

There is not a front licensing mounting bracket, on a Chrysler Sebring. The Chrysler Sebring has a rear license plate mounting bracket.


Where is the starter on a 1997 Chrysler Sebring convertible?

It is on the front of the engine, behind the motor mount bracket.


Where is the brake light switch on a 1999 Chrysler Sebring convertible?

It is on a bracket, just above the brake pedal.


Where is the starter on a 2.7 Chrysler Sebring convertible?

It is on the radiator side of the engine, behind the motor mount bracket.


How do you replace windshield washer pump Chrysler sebring convertible?

The windshield washer pump on a Chrysler Sebring convertible is replaced by disconnecting the wiring harness and unbolting the pump. It can then be lifted from its mounting bracket and a new pump put into place.


Where is the brake light switch on a 2004 Chrysler Sebring convertible?

It is mounted on bracket just above the brake pedal.


Where is the starter on a 2000 Chrysler Sebring convertible?

It is on the front of the engine, behind the engine mount bracket.It is on the front of the engine, behind the engine mount bracket.


Where is the starter on a 1999 Chrysler Sebring convertible?

The starter is on the front of the engine, behind the engine mount bracket.The starter is on the front of the engine, behind the engine mount bracket.


Where is the brake light switch on a chrysler sebring?

On the bracket the brake pedal mounts to.


Where is the brake light switch on a 2002 Chrysler sebring?

On a bracket, above the brake pedal.


Where is the stop light switch on a 2002 Chrysler sebring?

It is on a bracket, just above the brake pedal.


Where is the brake light switch on a 1997 chrysler sebring?

On the brake pedal bracket under the dash.On the brake pedal bracket under the dash.


Where is the starter on a 2005 Chrysler Sebring?

It is on the front of the engine, behind the engine mount bracket.It is on the front of the engine, behind the engine mount bracket.


How do you adjust convertible tops on a 2002 Chrysler Sebring convertible?

you have to remove the rear seat than the seat belt bracket and than the seat back after that you have to remove the rear panels whwre the speakers are after all that is off there are three bolts 13mm I believe loosen them close your top and tighten bolts with top latched.


Where is the starter on a 1999 Chrysler Sebring 2.5 liter v6?

It is on the radiator side of the engine, behind the motor mount bracket.


Where is the starter on a 1998 Chrysler Sebring?

It is on the radiator side of the engine, above the oil pan, behind the engine mount bracket.


Where is the starter for 2001 2.7 liter Chrysler sebring lxi?

It is on the front of the engine, behind the engine mount bracket.It is on the front of the engine, behind the engine mount bracket.


Where is the power steering pressure switch for a 1993 chrysler new yorker?

The power steering pressure switch, on a 1993 Chrysler New Yorker, is located below the power steering pump. The pressure switch is attached to the power steering reservoir mounting bracket.


Where is the starter located on a 2005 Chrysler sebring?

Front center of the engine, behind the motor mount bracket.Front center of the engine, behind the motor mount bracket.


Where is the stoplight switch on a 2002 Chrysler Sebring sedan?

The stop lamp switch is on a bracket above the brake pedal.The stop lamp switch is on a bracket above the brake pedal.


How do you change the battery in a 1997 Chrysler Sebring Convertible?

Jack the front up, take off the drivers side wheel/tire, remove the plastic wheel house liner 6 screws (you will see), remove negative terminal, remove positive terminal, remove bracket that holds battery, reverse order to install.


Where is the fuel cut off switch on a 1997 Chrysler sebring?

1997 chrysler sebring does not have a fuel cut off switch. Fuel pump is controlled by a relay located on the firewall right above the battery. Its on a bracket that holds 3 relays. The relay you are looking for is in the middle. Also called a auto shut down relay


Where is the freeze plug on a 1996 Chrysler Sebring Coupe 2.5?

Look under the exhaust manifold on the side of the motor facing the radiator. You have to drop the manifold and the oil filter bracket to change it.


What is the bracket called that holds the caliper?

Caliper mounting bracket or steering knuckle. It depends on if the bracket is a separate part of the knuckle or not.


Changing to headers on 350 small block where does the power steering go?

The power steering stays where it is at. There is only 1 bracket that won't hook up and that is the one that bolts to the factory exhaust manifold. You will have to modify that bracket are make a bracket that will hold the power steering pump and keep it from moving.