answersLogoWhite

0


Best Answer
Copy

The Park switch is located in the wiper motor housing and is not replaceable. Please go to local junk yard and get another wiper motor and install. Please note the plastic switch components are a poor design and made with brittle plastic. Also please use a lubricant from a hobby store that can be used on plastic components and won't make the plastic more brittle.

Thank You for asking.

Jim

User Avatar

Wiki User

โˆ™ 2009-11-07 21:16:34
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you get to the park switch or wiper motor on a 1997 Lincoln Town Car?
Write your answer...
Submit

Related Questions

What are the dip switch settings on a 1997 sunfire windshield wiper motor?

Please clarify or explain what you are trying to accomplish. There are no dip switch setting on that wiper motor that I have ever seen.


How do you replace rear wiper motor 1997 Ford Explorer?

how do you replace rear wiper motor on a 1997 ford explorer


How do you install wiper motor for BMW 740il?

wiper motor not working on my 1997 BMW 740IL


The windscreen wipers on my 1997 punto won't work any ideas what it could be?

Fuse blown Wiper switch faulty wiper motor faulty both wiper arms have come loose on the spindles.


How do you replace the wiper motor on a 1997 Chevrolet C1500 pickup?

Remove the wiring harness from the wiper motor. Remove the wiper arm linkage. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.


How do you remove the windshield wiper motor on a 1997 Nissan Maxima?

* Remove the windshield wiper arms * Remove the cowl cover * Disconnect the electrical connectorr from the wiper motor * Detach the wiper motor/linkage assembly from the cowl * Remove the wiper motor retaining bolts and remove the motor


Where is the wiper switch on a 1997 Nissan Sentra?

London


How do you prevent the windshield wipers from running regardless of the wiper switch position on a 1997 Toyota 4Runner?

unplug the wiper motor under your hook, its located at the back of the engine compartment on the passenger side


How do you replace wiper motor on a 1997 mercury grand marquis?

how do you get to and replace the wiper moter on a 97 marquis


The rear wiper motor for your 1997 Jeep Wrangler Hardtop has three wires When you connect only two to a switch you are able to operate the wiper Why are there three wires?

The three wires are the ground wire, the hot wire that runs through the switch and is energized only when the switch is in the on position and the third wire which is energized anytime the ignition switch is on. This circuit allows the wiper arm to go to the "park" position when you turn the wiper switch off. If you turn the ignition switch off while the wiper is in operation it will stop immediately and not continue to the "park" position. When the ignition switch is turned on again, the wiper will return to "park".


Is the wiper switch connected to the ignition switch on a 1997 ford f150?

no. Make sure wiper is in "OFF" position before you turn off your car.


How do you change the rear wiper switch in a 1997 Mercury Villager Van?

The switch just pops out of the dashboard.


Where is the wiper motor pulse board located on 1997 Chevy s10 pickup?

It is attached to the wiper motor. It can be easily changed without removing the wiper motor. Unplug the wire harness to the wiper motor, remove the three small screws holding the cover in place, remove the cover, remove the pulse board.


Where is the pulse board located on a 1997 GMC Sierra?

On top of wiper motor


Where is wiper motor on a 1997 Dodge Caravan?

It is under the cowl below the windshield


How do you change wiper motor in 1997 Chevy truck?

You must first remove the wiper arms. then, remove the screws holding the black plastic grill under the wiper arms. This will expose the motor. You will then need to disconnect the wiper arm transmission linkage from the motor, the remove the three bolts holding the motor on. Install in reverse order.


1997 buick park avenue windshield wiper switch removal?

The windshield wiper switch is located underneath the windshield wiper lever. Remove the upper and lower steering column to gain access. Loosen the mounting screws and unplug the switch. Pull off the switch from the steering column.


Where are the wiper relays on a BMW 316i 4 door. 1997 model?

The BMW 316 windshield wiper relay switch is located on the firewall in the engine compartment. The wiper relay switch will be in the middle of the firewall, near the top.


Where is the windshield wiper washer motor on a 1997 Oldsmobile cutlass?

Check either at the bottom of the windshield washer fluid reservoir or check to see if the wiper motor has washer hoses connected to it


Your wiper delay dose not work right they come up but do not go back down like they should please help you changed the motor on a 1997 cheve venture van.?

if the new motor came with a new circuit board (wiper pulse board), then the only thing left is the switch on the steering column


How do you remove a front wiper motor on a 1997 expedition?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


Installing windshield wiper motor for a 1989 ford expidition?

Ford Expeditions where built from 1997 & UP... Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ONposition. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


How do you remove a 1997 Ford Expedition winshield wiper transmission there doesnt seem to be clearance to get it out.?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


How do you fix a 1997 GMC truck windshield wiper motor?

take it to your gm dealer it was a recall


Does one motor control both windshield wiper blades on a 1997 Nissan Sentra?

YES