0
If there are 3 wires, then, black, ground, white to your headlight fuse on the fuse box. This way the ligthts will brighten and dim with your dash lights, and green, to the neg., coil. If there is a fourth wire, it will be red, and will go to a direct power source. I would go to the cig., lighter fuse, on the box. It is always hot, and runs a big fuse, and the lighter is hardly ever used.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you hook up a sunpro tach to a 98 Toyota tacoma 2.4l 5 speed?
how do you hook up a sunpro super tach 2
How do you hook up a sunpro tach to a 96 vortec 350 5.7?
well dip$hit gmc make vortec
How do you remove and install wiper arms on a 1994 Plymouth Voyager?
Many Plymouth Voyagers have the J-hook wiper arm. A person has to bring the old blade up, push it down over the hook, and then up over the hook. Next put the new blade over the hook, push it down so the hook goes through the hole, and then back in to catch the bar.
Who sings On the cover of Rolling Stone?
It was a hit song for Dr. Hook & the Medicine Show in 1973.
Where do you hook up the tach wire on 1973 nova?
Negative side of the coil. David G,
How do you hook up a Sunpro tach to an MSD ignition?
There should be a tach output connection on the side of the box somewhere, you just plug your tach pickup into that. If it doesn't work you'll need a MSD tach adapter. I'm unsure of the part numbers but there are 2 different ones, it depends on what you used to wire in your ignition. If you used the white wire there is one and if you used a magnetic pickup ( green and violet wires ) there is another one....MSD-8920. I have a sunpro tach and I had to go out and buy an adapter to make it work...for about 50 bucks.
How do you change wiper blades on a 1996 Plymouth grand voyager?
The 1996 Plymouth Grand Voyager has the most common hook-end wiper arms. See Sources and Related Links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.
How do you install a sunpro super tach 2 in a 73 Chevy Nova?
Should have four wires: Positive, Ground, Light, and Tach. Put ground first! I made this mistake and took out all the lights in my dash. Hook the tach wire up to the male end on the distributor cap (you'll have to route it through the firewall). Hook the positive up to a nearby wire or open spot in your fuse box. I tapped off the radio. Hook the light into your panel instrument light circuit.
Is there any way to hook up a super tach 2 rpm x 1000 to 1981 Chevy truck?
Hello, I found the owners manual for the sun super tach 2 on Sunpro's website. This is the addy. http://www.sunpro.com/publish/2007/09/27/pdf_english_16472.pdf Hope it helps.
How do you replace the rear wiper of a 1998 Plymouth grand voyager?
The 1998 Plymouth Grand Voyager has the most common hook-end wiper arms on front and rear. See Sources and Related Links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.
How do you install a Sunpro super tach 2 tachometer in a 1994 Silverado?
hook your green wire from the tach to the white wire from the coil PAC it should be a white and a yellow wire coming from the coil. the tach should have a white wire that will be your light inside the tach a red wire for power and a black for ground.. good luck
In what order do the spark plugs hook up on the distributor cap on a 1973 Ford?
the firing order is cast in to the intake manifold
