0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is difference between impact load and sudden load?
sudden load differ from impact load by the velocity of loading
What are the three classes of levers and an anatomical example of each one?
First Class Levers The fulcrum is between the input force and the load Always changes the direction of the input force and can be used to increase the force or the distance Second-class levers The load is between the fulcrum and the input force Does not change direction of the input force Output force is greater than the input force. Third-Class lever The input force is between the fulcrum and the load Does not change the direction of the input force Output force is less than input force.
What are damper winding?
damper winding help to maintain the magnitude phase shift (on load chages) between rotor an stator flux and kill some parasite currents produced by the leakage flux moving out the rotor winding to the rotor core.
What has a pivot point between a load and an input force?
The answer is: a lever.A lever is a simple machine that has a stick that pivots at a point called a Fulcrum.There are 3 types of Lever:First class lever: A first class lever is when a fulcrum is in the middle of the input force and the load. An example is a seesaw in the playground. When you press down the side of seesaw,(input force) the other side goes up. (load, output force) In the middle, there is a fixed point.Second class lever: A second class lever is where you have the load in the middle of the Fulcrum and the input force. An example would be a wheelbarrow. The basket in the middle is the load( also called the output force) the wheel at the end is the Fulcrum, and the handle that you press up and down is the input force.Third class lever: A third class lever is a lever that has a input force in between the Fulcrum and the Load. An example is a Hammer. The sharp part is the load(output force) the part you grab and swing is the input force, and the other end of the hammer is the Fulcrum.
What are input impedance in a load cell?
The resistance measured across the excitation terminals of the load cell, when the output terminals are open.
What is difference between impact load and sudden load?
sudden load differ from impact load by the velocity of loading
What is the input and output of a load cell?
The input of a load cell is the force or weight applied to it. The output of a load cell is an electrical signal, typically in the form of voltage or current, that is proportional to the applied force or weight.
Where is the load sensor valve on a ford escort van located?
IN FRONT OF THE OFFSIDE REAR DAMPER
Why a high input impedance?
A circuit (an amplifier) typically has a high input impedance so that it does not unduly load the input circuit. Any such load could cause distortion, and that is generally not desired.
Why Vw polo 1.0 mpi change the sound when isn't on the move?
because the movement's load functions as a damper
No-load and full load transformer?
A: a transformer will follow the rule of input output ratio with no load. As soon as a load is applied there will be changes in the ratio
What is the mechancial advantage of lever that can lift a 100 N load with an input force of 20 N?
The mechanical advantage of a lever is that it can lift a 100N load with an input of 20N is calculated as is 5. In this case, the effort is divided by the load.
How a zener diode is used in voltage regulator under both varying input and varying load condition?
In the varying input condition, the zener diode is used in such a that any variation in the input voltage,should not in any affect the load (that is the arrangement supplies just the voltage needed by the load no matter how high or low the supply voltage might go). In the varying load condition, the zener diode is connected in such a way that any change in the load voltage should not affect the input voltage.
What are the three classes of levers and an anatomical example of each one?
First Class Levers The fulcrum is between the input force and the load Always changes the direction of the input force and can be used to increase the force or the distance Second-class levers The load is between the fulcrum and the input force Does not change direction of the input force Output force is greater than the input force. Third-Class lever The input force is between the fulcrum and the load Does not change the direction of the input force Output force is less than input force.
What are damper winding?
damper winding help to maintain the magnitude phase shift (on load chages) between rotor an stator flux and kill some parasite currents produced by the leakage flux moving out the rotor winding to the rotor core.
What is the difference between impact strength and toughness?
impact strength is sudden load bearing capacity & toughness is steady load bearing capacity.
How many ohms is the sending unit putting out?
Usually is the input impedance of the load 10 times higher than the input impedance of the sender. So the sender's ohms is one tenth of the load.
