answersLogoWhite

0


Best Answer
Copy

I have a 98 Suburban with the 5.7 vortec V8. The cam sensor is in the distributor. Remove the cap and rotor to get to the sensor. Hope this helps.

2006-09-02 18:08:17
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

Is there a crank sensor on a 93 suburban?

NO. A crank sensor are cam sensor was not introduced until the year 1996.


Does a Chevrolet 2.2 have a cam position sensor?

The 94 and 95 are the same,no cam sensor.1996 and 1997 are differant in one way.The 1996 and 1997 have a cam sensor. .The 97 has a cam sensor and the 94 does not.The 1996 has a cam sensor too.


Does a 1988 Chevy suburban have a camshaft position sensor?

No it does not. It has a distributor no need for a cam sensor.


How do you replace the cam sensor on 1996 dodge 5.2?

Unbolt distributor cap. lift rotor off, remove and install new cam sensor (pick up plate) and reinstall rotor and cap.


Does a 94 Chevrolet suburban have a cam sensor?

No it does not. That engine still has a distributor.


Where is cam sensor on 1996 Chevy truck?

It's in the dist. The dist. itself is the cam sensor.


Where is the cam sensor located on a 1999 Chevy suburban?

The 1999 Chevy Suburban camshaft sensor is located on the front of the engine. The camshaft sensor will be behind the front engine cover.


Where is the camshaft position sensor a 1996 jeep classic 4.0 6cyl?

The cam sensor is inside the distributor.The cam sensor is inside the distributor.


Where is the cam shaft position sensor located on a 1996 Cherokee sport 4.0?

The cam sensor is inside the distributor.


What is wrong if a 1996 Chrysler Sebring computer reads 'cam position sensor no signal'?

There is a problem with the cam sensor or the wiring to it.


Where is the cam position sensor for 1996 Saturn?

there is no cam sensor on any 1996 saturn- i presume there is a code p0341 set- check the 1/4 plug wires, plugs, and coils


How much does a cam sensor on a 96 mercury villager cost?

The cam sensor on a 1996 Mercury Villager cost about $35 to $40. The sensor is actually manufactured by a Nissan subsidiary.


Where is the cam sensor located on a 1996 Chevy blazer 4.3?

In the distributor.


Why doesn't your 1996 Ram 1500 5.2 have no spark and no fuel and just cranks but no fire?

either crank sensor or cam sensor. but more then likely its the cam sensor located in the distributer.


Where is the camshaft sensor on a 1996 4 liter grand Cherokee?

The cam sensor is inside the distributor under the rotor.


Cam position sensor location for 1996 Dodge Intrepid?

Cam sensor on 1996 Dodge intrepid 3.5 V6 is on the driver's side on top where the cam gear turns on the front of the engine.. Usually has a 90 deg. connector for the wires.. MUST be air gapped correctly to work proplerly.. DO NOT Bottom the sensor out against the cam gear unless the new sensor has a card board disc glued to the end of the sensor to set the gap... Good luck!


Is the CPS on a 1996 5.2 in the same place?

The crank sensor is on the top driver side of the bell housing. The cam sensor is inside the distributor.The crank sensor is on the top driver side of the bell housing. The cam sensor is inside the distributor.


Where is the cam position sensor on a 1996 Plymouth voyager with 3.0 liter engine?

The camshaft position sensor is inside the distributor.


Why does your 1996 Lincoln mark VIII have no spark?

ck cam shaft sensor, check crank shaft sensor also.


How do you change the cam sensor f250 diesel?

for a 6.0L engine the cam sensor is located on the side of the block behind the power steering pump. disconnect the wiring connector, remove the 8mm bolt, remove sensor and reverse to install.


Where is the cam sensor on a 1996 Chevy Lumina?

under neath the power stearing pump.


Where is the cam sensor located in a 4.0 engine in a 1996 Jeep Cherokee Laredo?

It is in the distributor.


Where is the cam position sensor on 1996 BMW 328i Convt e36?

The 1996 BMW 328 camshaft position sensor is located on the front of the cylinder head. The camshaft position sensor should be labeled as such.


How do you replace the camshaft sensor on a Chrysler Sebring 1996 2.5l v6?

The cam sensor is part of the distributor. You have to replace the entire distributor.


How do you change the cam sensor on a 1996 Chrysler Sebring 2.5?

You have to buy and replace the entire distributor.