Before this is started you need to know that you will need a large pop rivet gun to complete installation. REMOVAL. With the window in the up position, remove door trim panel and plastic water shield. Secure the glass in the half way up position with door stops wedged in between the window and door.Do not proceed til you are sure the weight of the glass is supported.Remove the rear guide channel nuts and and take the assembly out of the opening. Punch or drill out the center pinsof the rivets that secure the window regulator in place.Unplug the electrical connector. Move the regulator until it is disengaged from the guide channel and lift through the acces hole. If replacing the window motor, make sure to place a screw in the slot to lock the regulator before separating the motor from the regulator to prevent the spring from unwinding and causing injury. INSTALLATION. Place the regulator in position in the door and engage to the guide channel assembly. Secure the regulator to the door using 3/16 inch manuel aor 1/4 inch power rivots and the rivet tool. Plug in the electrical connector Tighten the channel nuts securely. Install the door trim panel
The lock switch has nothing to do with the window. If you have power windows and the window switch is bad, you can operate the window by jumping the wires on the switch plug. On my 91 Camaro RS, the window regulator (motor) stopped working. I bought a new regulator at Napa and replaced it. Replacing the window regulator requires drilling out the factory rivets. IMPORTANT! Before you start,you should drill a hole through the door and gear then install a temporary nut & bolt to lock the window in the up postion. This will prevent the window from falling while your fingers are near the gear.
To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.
You must replace the entire regulator.Here's howhttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator
1. Remove the power window regulator2. Install a pan head sheet metal tapping screw through the sector gear and the backing plate at the hole provided to lock the sector gear into position. Then drill out the motor to regulator attaching rivets.3. Remove the motor from the regulator.To install:1. Lubricate the motor drive gear and the regulator sector teeth. Install the motor to the regulator and check the mesh of the motor to the regulator.2. Install rivets to the motor and the regulator.3. Remove the sheet metal tapping screw.4. Install the power window regulator.
You have to disconnect the glass from the regulator or clip the regulator cables.See this post for instructionshttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator
you have to get the panels and the window regulator. get window switches and wire it all up good. you should be fine. a real pain, but it can be done.
You have to disconnect the glass from the regulator or clip the regulator cables.Here's howhttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator
The best explanation I have seen is found here: http://www.fullsizechevy.com/forums/general-discussion/tech-articles2/351094-99-02-nbs-power-window-regulator-motor-replacement.html It has pics that should help a lot.
usually by replacing window regulator.
Remove the window regulator assembly from the door.Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.Connect the window motor to the regulator with 3/16 in. rivets.Install the window regulator assembly.
First, remove the switch panel by prying it out and disconnecting the electrical?æconnectors. Pry away the trim panel so that you can get to the mechanical workings of the window. Remove the fasteners that hold the regulator to the door and then remove the regulator. Install the new regulator and put the door back together.
window regulator