0
I did it the easy way. I bought a BRASS compression coupling (Plumbing supply House) , Plastic won't take the tightening required for a pressure seal.
I just hack sawed off the "tee" part and connected the 2 straight sections with the Brass coupler. I have replaced my Well Saver LPT20 twice over the years with this technique. They tend to rust out underneath at the weld after several years.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How much vacuum is created by centrifugal pump during empty out the tank?
If we install centrifugal pump to transfer liquid from tank,after empty out the tank pump is continiously running,then how much vacuum is created in tank?
Cost to install a hot water heater?
30gal.hot water tank cost+installation
What if your toilet does not have a tank ball or flapper?
Mine has neither and it works perfectly I install this type all the time
Can you shut off the cold water intake to hot water tank to stop a leak not in hot water tank?
Yes, but there still is all the water stored in the tank plus the water stored in the existing hot water lines throughout your home that will eventually leak out.If you intend to install a hot water heater (HWH) yourself and you do not have valves to isolate the existing plumbing then turn off your main water supply, drain the water from your home using the lowest level sink, then attach a hose to the bottom of the HWH and drain the tank. When you install the new HWH install new shutoff valves. (Hint: Check with your local city plumbing and see if an expansion tank is required.)
Does the Ontario plumbing code require install of an anti-scald device for domestic hot water?
Yes. If you change any fixture or hot water tank you must install a valve that limits the hot water delivery at the new fixture to 48C. If you change the hot water tank you must either put a valve on all fixtures except the diswasher and clothes washer or add a mixing vavle on the output of the tank.
How do you install a diesel auxilary fuel tank?
depends what you want to install the tank in if it is in a pickup, there are easy to install tanks available that sit in bed of truck some also have tool boxes built in
How do you install fuel pump on 2002 Nissan maxima?
Remove fuel tank, replace pump from top of tank, re-install. Change the fuel filter while your at it!
How do you install fuel pump on 2002 Lincoln?
It is you gas tank; empty all gas out, then drop tank.
How do you install a fuel pump on a 1989 Pontiac TransAm?
The gas tank has to come down as the pump is in the tank.
How much money will I have to invest if I were to buy all the material to install it myself?
You will not be able to install your own septic tank.
How do you install in tank gas pumps?
Unless there is an access hole in the rear area of vehicle you have to drop the fuel tank- there is access at the top of the tank for replacement
How do you install a gas tank on 69 Chevelle?
hoist up into place and tighten down the 2 gas tank straps to hold the tank in place, hook up the hot wire to the fuel sending unit and ground wire to the car body and then install the fuel line to the tank and your done.
How do you install a hot water recirculating line to accomadate the most remote fixtures.?
Install line from the outlet of the tank and run line to the last fixture and bring it back to the bottom of tank with a pump
How do you install fuel tank on 1995 f-350 turbo diesel?
which tank you want to install? front or rear. 1995 f350s have 2 tanks and a switch on dash to swap from front to rear.
How do you install an in gas take fuel pump on a 1989 Dakota V6 3.9?
Remove fuel tank--access at top of tank Remove fuel tank--access at top of tank
How do you install a fuel pump on 300zx?
On z31 its located in the gas tank, you need to remove the tank. Z32, you don't have to remove the tank but you have to remove the panels in the trunk to access it from the top of the tank.
How do you install a new gas pump assembly?
Remove the gas tank.
