answersLogoWhite

0


Best Answer

Take off distributor cap, it will have two screws mounting it directly to the ditributor. Unscrew the two screws (probably a 5.5 mm), unplug the wires to it, install the new one and you are set.

User Avatar

Wiki User

โˆ™ 2008-09-30 22:45:25
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you install an ignition control module in a 93 Chevy full size sport blazer?
Write your answer...
Submit
Related questions

How do you change the Ignition Control Module in a 1995 Blazer S-10?

Remove the wiring harness from your 1995 Chevy Blazer ignition control module. Remove the ignition control module retaining screws. Reverse the process to install your new ignition control module.


Where is the ignition control module located an a 1983 Chevy blazer?

Where is the control module located on the 1983 Chevy blazer


Where is a ignition control module a 1987 Chevy blazer s10?

The ignition module is located in the distributor, under the distributor cap.


How do you replace the ignition module on a 1993 Chevrolet Blazer?

Find your distributor cap and follow the center cable to a rectangular part. This is the ignition module. Remove it, get a new one and install it.


Where is the location of the electronic spark control module 2000 gm?

The ignition control module on a 2000 Blazer with the 4.3 is mounted on the same bracket that the coil is mounted to.


Where is the ignition control located on a 1981 Chevy Blazer?

Depending on what type engine you have, the ignition module may be an integral part of the distributor cap.


What is a ignition control module?

the ignition control module is operated by the pcm,the pcm tells the ignition control module when to energize the coils to enable spark


How do you install a electronic ignition control module?

The electronic ignition control module on an automobile is installed by first locating the unit at the top of the engine. The wiring harness is then disconnected from the original unit an a new module put in its place.


How do you bypass the ignition module to crank a 2000 Chevy blazer 4.3?

It will not run if you bypass the ignition module (no spark).


Where is the ignition control module on a 1994 aerostar?

The 1994 Ford Aerostar ignition control module is located on the firewall in the engine compartment. The ignition control module will be on the drivers side of the firewall.


How do you change an ignition module in a 1993 Chevy blazer?

your a fatty


Where is the location of the ignition control module on a Ford Focus?

You can find the Ford Focus ignition control module beneath the drivers side dashboard. The ignition control module will be above the accelerator pedal.


Where can you find a schematic for the ignition control module of a 43 vortec engine in a 1994 Chevy Blazer S10?

Owners manual, positive.


Where is the ignition control module located on a 1996 Chevrolet blazer located?

If you remove the distributor cap, you will see it bolted on the base plate


Where is the ignition switch module located on the 1988 Cherokee limited?

module locatedwhere is the module on a 9 Chevy blazer


Where is the ignition control module in a 1997 mercury villager?

The ignition control module sit directly below the distributor.


Where is the ignition control module on a 1992 Crown Vic?

Where is the ignition control module located in my 1992 Crown Victoria


Where is the ignition module on a 88 tracer?

ignition control module is under the distributor cap


Were is the ignition control module on a 2001 Mercury Sable 3.0 dohc?

Where is ignition control module on a 2001 mercury sable


Where is the ignition control module on a 97 explorer sohc?

Only the EEC-IV ignition systems ( 1991 to 1995) use an external ICM (ignition control module) . From 1996 on with the EEC-V system the ignition control module is incorperated into the power control module (PCM) mounted in your firewall on the passenger side.


Where can i get ignition control module for Mercedes Benz 300SE?

A Mercedes-Benz 300SE ignition control module can be obtained from most Mercedes-Benz dealerships. The ignition control module, can be purchased at most auto-parts stores.


Where is the wcm on a 2006 dodge magnum?

The ignition switch is part of the WCM (wireless control module).The ignition switch is part of the WCM (wireless control module).


How do i change the ignition module in a 1998 suburban?

Begin by removing the wiring harness from your 1998 Chevrolet Suburban ignition module. Remove the ignition module retaining screws. Reverse the process to install your new ignition module.


Where is the ignition control module 1997 Chevy cavalier 2.2 L?

where is the ignition control module loacted on a 1997 chevy cavalier


Where is the ignition and distributor located on a 1990 Chevy Celebrity?

The 1990 Chevy Celebrity engine is distributorless, the ignition is handled by a combination of the engine control module(computer) and the ignition control module. You did not mention which engine the car has. If your car has the 4 cylinder engine the ignition control module is below the intake manifold at the rear of the engine. You can follow the spark plug wires to it. The coils are mounted to the ignition control module. If your car has the V6 the ignition control module is near the starter and again you can follow the spark plug wires to it. Again the coils are mounted to the ignition control module.