0
Remove the tire and wheel. Remove the brake assembly and rotor. Remove the ball joint retaining nut. Pound the ball joint out with a hammer. Reverse the process to install the new ball joint.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How do you replace a ball joint for 1997 dodge van b3500?
For the lower ball joint, remove the lower control arm and the ball joint seal. Press the ball joint from the control arm. Press the new ball joint into the lower control arm ensuring it is fully seated, install a new seal and the lower control arm.
How do you remove and install ball joints in a Dodge Neon 1995?
Remove the tire and wheel. Remove the ball joint nut. Pound the ball joint out with a hammer or mallet. Reverse the process to install the new ball joint.
How do you replace a lower ball joint on a bravada?
You will need to remove the tire and wheel from your Oldsmobile. Remove the retaining not on top of the ball joint. Pound the ball joint out. Reverse the process to install your new lower ball joint.
How do you install front ball joint on a 99 Cadillac Escalade?
What kind of lower ball joint is used, on a cadillac escalade
Lower ball joint on 06 dodge ram 4x4 get pushed down or up to remove?
Unless common practice has changed, you should have to press the lower ball-joint down through the bottom of the lower A-arm to remove the joint.
How do you install 2007 dodge caliber ball joints?
Type your answer here... how to install lower balljoints on 2007 caliber
How do you replace lower ball joint on 93 Mercury Cougar?
Remove the tire and wheel from your 1993 Mercury Cougar. Remove the ball joint retaining nut. Pound the ball joint out with a hammer. Reverse the process to install your new ball joint.
How do you remove the lower ball joint on a 97 dodge Dakota sport that has pins?
Check with a dealer- ball joints on series of Dodge products where covered by recalls.
How do you change ball joints for a 2001 dodge ram 1500 2wd?
Remove the tire and wheel. Remove the retaining nut from the top of the ball joint. Pound the ball joint out with a hammer or mallet. Reverse the process to install the new ball joint.
How do you remove the lower ball joints on a 1995 Oldsmobile ciera?
remove tires, remove both caliper bridge bolts, put caliper on upper control arm, remove rotor, take out lower ball joint bolt, using pry bar or pipe separate lower ball joint, if not lose already use pickle fork or a bar to put pressure and separate, move steering knuckle away from lower ball joint, use air hammer or equiv. and push rivets out of ball joint. once all three rivets are pressed out ball joint will fall out and re install. install ball joint, some come with bolts and nuts. factory control arm will only come with new riveted ball joint. put bolts and nuts on new ball joint, tighten install zerx fitting, re-attach steering kuckle to ball joint by pushing down on the lower control arm and then forward on the knuckle. to align ball joint with hole on knuckle. re-install new ball joint bolt. once tight grease zerx fitting. re install rotor, caliper ect.
How do I replace lower ball joints on 1999 Chevy lumina?
Remove the tire and wheel from your 1999 Chevy Lumina. Remove the nut on the top of the ball joint. Pound the ball joint out with a hammer. Reverse the process to install the new ball joint.
How do you replace the ball joint of a Oldsmobile aurora 98?
Lower Ball Joint ReplacementSpecial Tools requiredJ 43828 Ball Joint separator1 Raise and support vehicle NOTICE: Care must be taken to prevent the drive axle joints from being over extended. When either end of the shaft is disconnected, over extention of the joint could result in separation of the internal components and possible joint failure. Drive axle joint voot protectors should be used any time service is performed on or near the drive axles. Failure to observe this can result in interior joint or boot damage and possible joint failure.2. Remove the tire and wheel assembly3. Remove the wiring harness from the lower control arm.4. Remove the stabilizer shaft link.5. Remove the cotter pin and the nut form the ball joint stud.NOTICE Failure to use recommended tool for separating the ball joint from the knuckle may cause damage to the ball joint and seal.6. Separate the ball joint stud from the steering knuckle.7. Remove the bolts and nuts from the lower control arm.8. Remove the rear crossmember bolts from the lower control arm.9. Remove the lower control arm from the crossmember.10. Put the control arm in a vice.11. Drill out the 3 rivets retaining the ball joint to the lower control arm. Use a 3mm run in drill bit to make the pilot hole through the rivets. Finish drilling the rivets with a 13mm run in drill bit.12. Remove the Lower control arm.Installation.1. Install the ball joint in the control arm.2. Install the 3 ball joint bolts and nuts. (tighten bolts to specs on ball joint kit)3. Install the lower control arm to the crossmember4. Install the rear crossmember bolts to the lower control arm. Tighten to 180 ft lbs.5. Install the bolts and nuts to lower control arm. Tighten bolts to 45 ft lbs.6. Install the steering knuckle to ball joint stud7. Install the nut to the ball joint stud. Tighten nut to 41 ft lbs minimum 55 ft. lbs max to install the cotter pin.8. Install cotter pin.9. Install the stabilizer shaft link.10. Install wiring harness to lower control arm.11. Install the tire and wheel assemblies12. Lower the vehicle13. Inspect the front wheel alignment.
