0
If it's indoors you would go to the local electronics store (i.e. radio-shack) And pick up two RG-59 cable ends and a barrel connector (sometimes called a coupling) Just put an end on each piece of cable, they will come with instructions, and then screw them together with the barrel.
You can also use wire nuts but it may cut down on the quality of the signal. Just strip off some of the outer sheath, and then a bit of the inner sheath. Twist the center copper wires together, and then twist the outer shield (silver mesh) together making sure that the copper wires don't touch the silver. If they do touch it won't do any harm, but it won't work.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What type of clamps used for armor cable?
The most common ones are RG59 and a low loss cable is RG 6,both are 72 0hm for tv sets and antennas.
How do you cut an armoured cable?
The use of armoured cable is determined by the application that needs an electrical source of voltage. It is a metal sheath cable classification. Armoured cable is used in applications that need mechanical protection usually below a certain elevation. Armoured cable is also usually used on surface wiring. If you have access to an electrical code book there is a whole section on armoured cable. In the CEC the section about armoured cable starts at 12-600 to 12-618.
What is a cable gland?
A cable gland is a connector which holds the end of a cable in place.
What is a load cable?
Load cable generally means the final cable before the actual load. So on a clothes dryer the "Load Cable" would be the cable running from the outlet to the actual clothes dryer.
Is a suspension bridge better than a cable stayed bridge?
NOcable stayed bridge is more preferred because if one rope is broken in it then tension is distributed in all other and we get time to repair it that means no sudden failure in it where as in suspension bridge if main cable is cut than it will be destroyed immediately.regardsmukulmukul_ce@student.iitd.ac.in
What type of wire is used for TV's or cable modem?
Televisions and cable modems use a coaxial cable. RG59 or RG6.
Is RG59 Coaxial Cable compatible with RG6 Coaxial Cable?
yes RG6 should be used exclusively for satellite hookups and digital CATV. RG59 is fine for analog CATV signals but will not support the higher bandwidth used for satellite signals.
Is cable coaxial the same as satellite coaxial?
Most times they are the same but a satellite signal needs to be carried by RG6 cable it is a heavier gauge wire then say RG59. Regular or analog cable signal is sometimes carried by RG59 but digital cable should use RG6. +++ The primary specification is not conductor size but the impedance and capacitance of the cable.
Will RG59 cable work for cable HD signal will 6 way splitter for normal cable work for HD cable?
Your first question, yes. Second question, no.
What kind of coax cable do i use rg58 or rg59 or wat type?
The type coax you need depends on the type service you have. For satellite service, we use a higher rated coax cable (RG6) to allow for a higher frequency for channels and back feeding capability. RG59 is a lower rated cable.
What type of clamps used for armor cable?
The most common ones are RG59 and a low loss cable is RG 6,both are 72 0hm for tv sets and antennas.
Can you use RG 59 on digital TV?
If the interface requires a co-ax cable, then RG59 is perfectly acceptable for video signals. It is not the best choice for arial or satellite feeds. RG59 suffers from high losses and therefore, will not be the right choice for a long run carrying HD signals. If the cable length is more than a few feet, it is probably wise to invest in something with a lower loss if HD is used now or will be in the future.
HOW MANYdBuVm in 75ohms?
The signal loss in a RG59 75 ohm coaxial cable should be of no concern unless you are running over a couple hundred feet. In that case use RG 6.
What is the difference between RG59 and RG6 cable?
rg-6 is a video cable that is used in today's new standards used to be rg-59 also called coax cable These cables are made for carrying RF (antenna signals) but can be used for video for short runs.
What is the function of a cable cutter?
To cut cable.
What is coupler plate for cable tray?
To join the pair of cable trays.
What is the cut off to join ME at GCT coimbatore?
Cut off for me 2012
