0
The most clean-looking way is to unsolder the resistor from the circuit board and put in its place a piece of solid wire, bent into a U shape to fit the same holes, soldering it back in place where the resistor was A slightly uglier but much faster way is to take the same U-shaped piece of wire and bend little hooks on each end. Hook the ends around the existing resistor leads and solder. The above assumes leaded through-hole resistors. If the resistor is surface-mount, you basically have to tack-solder a tiny loop of wire to each end of the resistor. Its best not to remove the resistor unless you're trained in surface-mount component repair, or you will likely damage the board. You will need an iron with a very small tip for this.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you define zero ohm resistor?
A zero ohm resistor is a piece of wire with a resistor body. It is essentially a jumper. It is useful when a jumper is need on a printed circuit board that is assembled by automated machinery, because the automated machinery can handle resistor insertion far easier than a jumper wire. The color coding on a zero ohm resistor is one single black band.
How to bypass fuel pump relay 98 Bui Park Avenue or were to connect a jumper wire?
Fuel pump relay 98 Buick at Park Avenue can be bypassed by locating the jumper wire that runs from under the dash to the "reader", and then create the "resistor pack" to jumper accross the wires.
What is the benefit of using zero ohm resistor?
A: Extremely important since at the level there is infinite current available at zero volts, In reality it can never be ac hived but it can be assumed for consideration Each piece of hookup wire can be thought of as a zero-ohm resistor. In fact even the hookup wire has resistance but it's so small it it can be neglected.
How do you know if your blower motor is bad or if you need to just change the resistor?
Use a jumper wire from the battery + (pos) terminal to the positive on the blower motor, and run a - (Ground) wire from ground on the motor, to chassis or frame.
Applications of zero ohm or resistor?
Zero-ohm resistors are used mostly in printed circuit boards in place of jumper wires. They have no to little resistance, so they are used to just connect sections of a circuit. The automatic insertion machines that create PCBs are not adept at connecting jumper wires, but can place zero-ohm resistors easily on the board.
A jumperless motherboard is likely to have one jumper Which jumper is it?
A bios or cmos jumper
What is jumper parking?
"Jumper Parking" is when you have a Jumper hanging on one pin for safe keeping, rather than using it to turn a Jumper Setting on.
How do you knit Ravenclaw jumper?
Find directions for a jumper and knit a blue jumper. If you are skills you could knit the Ravenclaw symbol onto the jumper otherwise you can buy the badges and sew them onto the jumper.
2001 Dodge Dakota air conditioner fan failed in mid use fuses and relays are good how do you remove fan switch and test?
Before taking the dash apart check the resistor. I have a 97 Dakota & it is located under the cowl. That resistor controls the fan speeds. You can check the switch using the resistor connecter. Pull connecter off resistor & use a 12 volt test light. Turn ign on & check for voltage at connecter on each fan speed. Have voltage then it is the resister or fan. (you can run a jumper wire from battery to fan to check it) No voltage then you go to the switch/wires etc. 95% of time it is the resistor.
How does a trampoline work?
Applied physics! The jumper uses muscles to generate energy. This energy is used to overcome gravity, and the when gravity returns the jumper to the tramp, the tramp "catches" the jumper. In catching the jumper, the tramp stores the jumper's energy in its springs, and then returns it to the jumper. Simple and easy.
What insect is a great jumper and why?
A grasshoper is a great jumper
What is a sloppy joe jumper?
large loose jumper
