0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why you need resistance in series with led?
limit current and avoid having it explode
What is the difference between over current and overload condition?
The term, 'overcurrent', describes either an 'overload current' or a 'short-circuit current'.An 'overload current' is a current that is higher than a circuit's 'rated current'. For example, if you have too many loads plugged into the same circuit, then the resulting current is an 'overload current'.A 'short-circuit current' is a large current resulting when a line ('hot') conductor accidentally makes contact with either a neutral conductor or an earth (ground) conductor.
Can a CMOS gate adequately drive a common LED?
You will have to check the datasheets for both the CMOS gate and the LED, then if the CMOS gate's rated output current is enough to light the LED you will need to do a little arithmetic using Ohm's law to calculate the resistor to put in series with the LED to limit current and avoid damaging the parts.
What is a heater overload?
overload heater is used to protect a large electric motor. If the overload heater get too hot from excessive current. its nomally-closed overload contacts wil open. interruptting the circiut of powe supply of motor
What is transient overload?
Sustained overload is overload that is continuous, or permanent. A resistive load is a good example. This is the kind of overload you get from simply plugging too many items into a circuit. Transient overload is overload generated by a reactive load, a momentary short circuit, or other temporary condition. An example of a reactive load is the compressor of an air conditioner starting. This kind of overload can be caused by a reactive load being added to an already moderately loaded circuit.
Can a capacitor be used as a fuse to limit overload current?
No, a capacitor can not be used as a fuse to limit an overload current condition.
Why you need resistance in series with led?
limit current and avoid having it explode
What is the Function of fuse in an electric circuit?
A fuse places a limit on the amount of current that can be drawn by an electric circuit by opening (blowing or melting) when the current exceeds a preset limit. This protects the circuit and the surroundings from fire or damage in the case of an overload or short circuit.
What is a functoin of a resistor?
esistors restrict the flow of electric current, for example a resistor is placed in series with a light-emitting diode (LED) to limit the current passing through the LED.
What is the difference between over current and overload condition?
The term, 'overcurrent', describes either an 'overload current' or a 'short-circuit current'.An 'overload current' is a current that is higher than a circuit's 'rated current'. For example, if you have too many loads plugged into the same circuit, then the resulting current is an 'overload current'.A 'short-circuit current' is a large current resulting when a line ('hot') conductor accidentally makes contact with either a neutral conductor or an earth (ground) conductor.
Why does a Led have a 470 resistor connected to the LED?
A: That resistor is there to limit the current to the LED it can be any value if the voltage is decreased or increased or no resistor if the voltage across the led is equal to the forward voltage drop.
How do you solve overload current?
Reduce the load.
Is a circuit breaker a resistor?
No, a circuit breaker is a safety device that is used in a circuit to limit the amount of current in an overload or short circuit condition. The number on a breaker is the top end current that the breaker will handle before opening the circuit.
How do you wire a 2V LED to run on 12V?
Light Emitting Diodes (LED) solid state devices are current dependant. LED have ratings for the max current allowed to the LED device. A typical current allowed to a LED is 20ma. Ohms Law is used to determine the resistance required to limit the current to your desired current. The formula is used in this manner: E=12VOLTS the desired current is I = 20ma. R = E/I = 600 ohms. Where E=2 volts dc and I=20ma R= E/I = 100 Ohms.
What are the features of ic 7812?
- Output current in excess of 1A - Internal thermal overload protection - No external components required - Output transistor safe area protection - Internal short circuit current limit - Available in the aluminum TO-3 package
Is four point starter is applicable to compound motor?
Yes! · To accelerate the motor to the rated speed · To limit the starting current in the armature to a safe value · To disconnect the motor in case of a supply failure or overload
Can a CMOS gate adequately drive a common LED?
You will have to check the datasheets for both the CMOS gate and the LED, then if the CMOS gate's rated output current is enough to light the LED you will need to do a little arithmetic using Ohm's law to calculate the resistor to put in series with the LED to limit current and avoid damaging the parts.
