0
How do you loosen bracket off CV joint on passenger side of 2002 mercury villiger van?
Wiki User
∙ 6y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you loosen the tension pulley on a 95 jeep Cherokee?
Loosen the 15mm nut that holds the pulley to the bracket then back off on the 13mm adjuster bolt.
How do you remove the alternator belt from a 1997 Plymouth Neon espresso?
first you need to jack up your car and put it on jack stands, then remove the passenger side wheel, then loosen the two bolts on the back of the power steering pump and the pivot bolt so you can remove the accessory drive belt. Then you can loosen the two bolts on the front of the alternator, then if you look at the alternator through the wheel well on the left side of the alternator there is a bracket, on the backside of the bracket there is an adjuster bolt loosen it and then you can remove the alternator belt.
How do loosen the tensioner for a serpentine belt on a 1987 crown vic?
depends on whether you are talking about the inside belt (closest to the engine) or the outside belt (closest to the cooling fan). Outside belt - loosen the alternator bolt at the top (the one that slides in the curved groove on the bracket) dont take it all the way out, just loosen it. On the bottom of the alternator there is another long bolt that needs to be loosened as well. The alternator should swivel in towards the engine giving enough slack to take the belt off or whatever needs to be done. Inside belt - The idler pulley (passenger side of the engine under the big a/c compressor) There is a bolt on the inside of the bracket that slides in a groove similar to the one on the alternator. It is hard to get to, but that is the only way to take the tension off the inside belt. Loosen the bolt on the inside of the bracket, then loosen the bolt on the outside of the bracket where the pivot arm bolts to the mounting bracket. The pulley should swing up towards the top of the engine giving the slack needed.
How do you disengage the alternator belt on a Ford F 150?
The alternator slides with the alternator bracket. Loosen the bolt that goes through the bracket into the alternator. You may need to loosen the bolt on the bottom as well. Don't remove either. Then slide the alternator towards the opposing pulley to loosen the belt enough to disengage.
How do you replace the belts on a 1995 Nissan 240sx?
loosen the manual tensioners and the alt bracket.
How do you change the belts on a 1993 Geo Storm?
The power steering pump has two adjuster bolts. Loosen the top bolt, and then the bolt underneath the pump (facing from passenger side) to give the belt some slack. The alternator has two adjuster bolts and one bolt to hold the bracket to the alternator. Loosen the bottom bolt (next to the belt), then loosen the top adjuster bolt. You should then be able to move the alternator towards the motor to slack the belt.
How do i adjust alternator belt on a 2002 protege?
you will find a bolt at top alternator connecting it to the bracket arm loosen it a little. you will find another bolt parallel with the bracket tighten it to pull the slack out of belt. tighten the bolt connecting alternator to bracket
How do you adjust the A.C. drive belt on a 1991 Toyota Previa?
loosen up the bracket that holds the tension on the belts then tigten up the adjustement bolts that pull the bracket then re tighten the bolts.
How do you replace the serpentine belt on a 6-cylinder 2002 Mercury Cougar?
Loosen the tensioner using a 3/8" drive, and off she comes. Follow the diagram on the passenger side strut tower to make sure you install the new belt correctly
How do you adjust the serpentine belt on a Kia Sephia?
It depends if you want to adjust the belt that does the a/c and power steering, or the one to the alternator. The power steering goes this way. First loosen the hex screw running through the power steering pump bracket. Then loosen the bracket hex screw that attaches to the belt tensioner bolt under the power steering pump. Then, tighten the tensioner hex screw that runs through the tensioner bracket. After you finish the adjustment, tighten all hex screws. If you adjust the belt for the alternator. You must loosen the alternator bracket hex screws on both the top and botom of the alternator. This requires going under the vehicle. Then, loosen the tensioner bracket hex screw and adjust the tensioner hex screw that runs through that. When you get the propper tension, tighten all screws and you are done.
How to replace power stering pump on 1996 dodge neon?
Disconnect both hoses and clamp them off. Remove the 2 bolts in the mounting bracket and loosen the bolt that mounts the bracket to the engine so you can slide the bracket out. Remove the belt by loosening the tensioner, then pull out the pump.
How do you remove 1992 Acura Vigor rear seat bottom?
The seats on a 1992 Acura Vigor use bracket which are found underneath and behind them. Loosen the bracket bolts to release the seats Pull them off and replace them.
