answersLogoWhite

0

No Problem to do this, but there are really no amplifiers with an output impedance of 8 ohms on the market. All loudspeaker amplifiers have an impedance of less than 0.5 ohm. Scroll down to related links and look at "Impedance bridging - Wikipedia".

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How many ohms would 2 16 ohm speaker cabinets and 1 8 ohm speaker cabinet calculate out to be?

If wired in parallel then 4 ohms.


What ohm should the speaker be if i want to achieve a 2 ohm load from 4 speakers?

Four 8 ohm speakers wired in parallel would give an effective 2 ohm load.


If an amp runs 1000 w rms at 1ohm how do you wire a dual 4 ohm speaker to run at 1 ohm?

the impedance of a speaker is a characteristic that is has. A 4 ohm speaker will always have a 4 ohm impedance and it cannot be changed. If 2 speakers of 4 ohm impedance are wired in parallel, then the total impedance will be 2 ohms. Similarly, if you wire 4 speakers together, the total impedance will be 1 ohm. Wiring a 2 ohm speaker to an amplifier rated to drive a 1 ohm load should work without any problems but expect the total power output to be somewhat lower than with a 1 ohm load.


Determine and draw the equivalent resistances when 1 ohm in parallel with 2 ohm?

The equivalent resistance of the parallel combination is 2/3 ohm.


What ohm speaker is best?

take a 2 ohm bridge into 1 ohm


What ohm load will 4 12 in dual 2 ohm play at?

There are a lot of possibilities here, especially since your question is worded exactly right.I'm taking it you have 4 12" speakers, each of which have Dual Voice Coils (2 Ohms each). You want to wire them together and see what ohm load you have.Ok, there's multiple ways to wire this up. Series, Parallel, and Series/Parallel combo.Wiring these speakers in series can give you either a 4 ohm load, or a 16 ohm load. 4 ohms if each speaker by itself (having DVC) is wired in parallel and 16 ohms if each speaker by itself is wired in series.Wiring these speakers in parallel can give you either a .25 ohm load, or a 1 ohm load. Again .25 ohms if each speaker by itself (having DVC) is wired in parallel and 1 ohms if each speaker by itself is wired in series.Wiring these in a series/parallel configuration can give you tons of different wiring options and ohm loads. In your case .75, 1, 3.2, 4 ohm loads.So your best option would to be wire your speakers up in series, with each speaker wired in parallel to itself. This way you'll get a 4 ohm load, if done properly. Make sure your amp can run a 4 ohm load too.


Will wiring a 16 ohm woofer with a 16 ohm tweeter in parallel result in a total ohm load of 8 ohms?

If you mean as pairs, yes. put an 8 Ohm and a 16 Ohm speaker in parallel for each channel. The 16 Ohm speakers will take 1/3 the power and the 8 Ohm speakers will take 2/3 the power. The resulting impedance will be 5.33 Ohms.


Can a 4 ohm receiver drive 3 ohm speakers?

If you connect four four-ohm speakers in parallel, the impedance will be equal to 1 ohm, and will allow the speakers to run at the advertised watt RMS. The equation is 1/(total impedance) = 1/(impedance 1) + 1/(impedance 2) and so on. Parallel is like this: Power source: + Speaker+: + + + + Speaker-: - - - - Power source: - However, usually if you hook up a 4 ohm speaker to a 1 ohm amplifier, it would still function it would simply not provide nearly as much wattage as it would have otherwise. Also, if your speakers are dual voice coil (like many subwoofers) you could use 2 4 ohm speakers, connecting the two voice coils on each speaker in parallel and then connecting the speakers themselves in parallel.


Can you run 4ohm resistor to make 4 ohms speakers 2 ohm?

Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.


2 ohm speaker dvc in series?

That would yeild a 4 ohm load


How do you wire two 4 ohm speakers into 2 a two ohm load?

Parallel


How can three resistors of 2 ohm 3 ohm and 4 ohm be connected to give a total resistance of 4 ohm?

2 in series with 3&4 in parallel