0
How do you program the car garage door opener in your 2008 Accra TSX?
Wiki User
∙ 13y ago
Your owner's manual gives instructions on how to do this. Follow their instructions to learn the "code" from your garage remote. The problem you will run into is that most modern garage door openers have what known as a "rolling code" that is constantly changing. So, when you program the button in the car, you'll have to perform a "learn" function on the actual garage door opener. (attached to the ceiling in your garage) You'll need somebody to hold the "learn" button on the garage door mechanism itself while you press the button on your TSX after the car has been programmed with your handheld garage remote.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you program the garage door opener in your 2008 Chevy impala?
The owners manual will tell you how to do it.
How do you program my 2008 Cadillac Escalade garage door opener?
escalde changed sometime in 2006 from homelink try www.learcar2u.com
How do you program garage door opener on Lincoln navigator SUV 2008?
Check Owner's Manual. If you do not have one. Check Related links below.
How do you program Ford explorer 2008 garage door opener?
Built in Explorer garage door openers are Homelink brand. Go to Homelink and it will ask you for vehicle information and garage door information. It will provide the exact step by step.
How do you program the garage door opener switch located on the visor on a 2008 Mercury Milan?
This information can be found in your owner's manual. If not call the toll free telephone # listed in your owner's manual for help.
How do you program the home link grage door opener in a 2008 Toyota Sienna?
Go to this site: http://www.homelink.com/
How do you set Garage Door Opener On 2008 Lexus IS250?
There are 3 programmable Homelink buttons you can use for different remotes. Just to the right of the buttons there is an indicator light. Decide which button you want to program. Point the none battery end of your remote 1"-3" away from the Homelink panel and press both the remote and desired Homelink button down and hold them down at the same time. After about 20 seconds, the Homelink indicator light will change from a slow flashing to a rapid flashing. You can then release both buttons, If the garage door responds to the Homelink, your done! If not, your garage door uses a rolling codes transmitter and must be trained. Find the training button on your garage door opener's transmitter (usually mounted on the ceiling). Press the training button and within 30 seconds press and release the programmed Homelink button twice. If the garage door opener operates, you're done! If not, press and release the Homelink button a third time and the garage door should respond. If it still does not, you may have a very old garage door opener with a none digital transmitter (like I did). In that case, you either need to buy a new opener or try to replace the transmitter with a modern digital unit (as I did). Advantage: cheaper than a whole new garage door opener. Disadvantage: The newer openers incorporate safety features that my old opener does not have.
What are the release dates for The Garage - 2008?
The Garage - 2008 was released on: USA: April 2008 (internet)
What are the release dates for The Boy in the Garage - 2008?
The Boy in the Garage - 2008 was released on: USA: 1 January 2008
What are the release dates for Gadget's Electric Garage - 2008?
Gadget's Electric Garage - 2008 was released on: USA: 16 April 2008
What actors and actresses appeared in The Boy in the Garage - 2008?
The cast of The Boy in the Garage - 2008 includes: Whitney Kaye as Sarah Jim Nystul as The Boy in the Garage
How do you program garage door opener on 2008 avalanche?
Garage Door Opener Programming - UniversalImportant: Do not use the garage door opener (GDO) with any garage door opener that does not have the stop and reverse safety feature. This includes any garage door opener model manufactured before April 1, 1982.Ensure that people and objects are clear of the garage door while performing programming operations.Programming the GDO for Rolling Code ReceiversThis procedure will learn a rolling code garage door opener to the GDO transmitter. The learn process must be completed within 30 seconds.Press the two outside buttons of the GDO for one to two seconds, then immediately release them.Locate the "Learn" or "Smart" button on the garage door opener receiver (located on the garage door opener motor-head unit). It is often found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Refer to the garage door opener operator's manual for assistance. Press the "Learn" or "Smart" button. The garage door opener operator's manual may provide assistance in determining when the unit is in learn mode.Immediately return to the GDO transmitter in the vehicle. Press and hold the button that is to be learned; the LED above the button will begin to flash slowly. When the garage door moves, immediately release the button. The LED will flash rapidly until programming is complete.Press the button used during the learn operation again in order to verify that the GDO transmitter has been programmed.The GDO is compatible with most, but not all, types of garage door openers. If the GDO LED does not flash rapidly after 90 seconds, there may be a compatibility conflict with the garage door opener.Programming the GDO for Fixed Code ReceiversThis procedure will learn a fixed code garage door opener to the GDO transmitter. To determine if the customer has a fixed code garage door opener, remove the battery cover on the customer supplied transmitter. If a row of dip switches is present, the garage door opener is a fixed code version. The transmitter should have anywhere from 8 to 12 switches. The garage door opener receiver may also have a set of dip switches. If the number of switches on the receiver and the transmitter do not match, use the receiver switches to program the GDO. Each dip switch may have either two or three positions. The two position switch can either be ON or OFF. The three position switch can either be ON, NEUTRAL, or OFF.Write down the positions of the dip switches. The positions of the switches will be entered from left to right into the GDO using the three buttons.Press all three buttons on the GDO for three seconds and immediately release them. The LEDs should flash slowly, indicating that the GDO is in programming mode.Enter the positions of the dip switches one at a time. If a position of a dip switch is on, press the left button on the GDO. If the position is neutral, press the middle button of the GDO. If the position is off, press the right button of the GDO. Enter all of the positions of the dip switches. The procedure must be completed in two and a half minutes.Press and hold all three buttons on the GDO until all the LEDs turn on.Press and hold the button that is to be learned; the LED above the button will begin to flash slowly. When the garage door moves, immediately release the button. The LED will flash rapidly until programming is complete.Press the button used during the learn operation again in order to verify that the GDO transmitter has been programmed.The GDO is compatible with most, but not all, types of garage door openers. If the GDO light does not flash rapidly after 90 seconds, there may be a compatibility conflict with the garage door opener.Erasing ChannelsTo erase programmed channels, press and hold the two outside buttons until the lights on the GDO transmitter begins to flash. Once the LEDs begin to flash, release both buttons; all learned codes are now erased.Individual channels cannot be erased, but can be reprogrammed using the procedures above
