Chevy Lumina

How do you put on a water pump pulley for the serpentine belt on a 1995 Chevy Lumina minivan?

323334

Top Answer
User Avatar
Wiki User
2012-05-25 16:47:14
2012-05-25 16:47:14

there should be 3 or 4 bolts that hold pulley on, just remove these bolts a pulley should come off. but remove belt first ! if pulley keeps turning while removing bolts. you can hold it stationary with a scredriver or similar.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The main pulley on which the serpentine belt goes on in a 1997 Chevy Lumina LTZ is the crankshaft pulley. The crankshaft pulley plays a role in the wheels turning and powering the alternator and power steering pump.

User Avatar

I belive that there is no adjustment on the serp belt on your lumina. Should be a spring loaded tensioner. If you are having problems with the belt slipping you most likely need to replace the belt/ tenssioner.

User Avatar

Typically, there is one pulley that is mounted on a spring arm to maintain proper belt tension. Just turn the bolt on the idler pulley and the tensioner will release.

User Avatar

You can change the serpentine belt by loosening the tensioner pulley. When the tensioner pulley is loose and the serpentine belt will become loose. Put the new serpentine belt on and tighten the tensioner pulley.

User Avatar

http://wiki.answers.com/Q/How_do_you_mount_a_serpentine_belt_on_a_chevy_lumina"

User Avatar

I want to take off the pulley wheel off,from a 1992 chevy lumina apv van.

User Avatar

usually serpentine belts get their tension(tightness) from the belt tensioner

User Avatar

Put the serpentine belt on to the pulleys of your 1994 Chevy engine. Tighten a serpentine belt with the tensioner pulley.

User Avatar

in the perimeter of the roof. between the headliner and roof.

User Avatar

Put the new serpentine belt on to your 1992 Chevy Corsica pulleys. Push the tensioner pulley to the left to tighten the serpentine belt.

User Avatar

It is behind the very BOTTOM pulley on the front of the engine. The big pulley.

User Avatar

Loosen the tensioner pulley on your 2001 Chevy Impala. The serpentine belt will become loose. Take the old belt off and put the new belt on. Tighten the new serpentine belt with the tensioner pulley.

User Avatar

If it is a serpentine belt you replace the tensioner pulley

User Avatar

on most cars it in the front at the bottom of the by the crank pully

User Avatar

The Chevrolet Lumina speed sensor can be found on the back of the transmission. The exact position of the speed sensor is dependent upon the year of the automobile.

User Avatar

take off the serpentine belt and crank pulley and you will need a harmonic balancer pulley to get it off.

User Avatar

the pulley is a press fit on pump shaft. need puller and installation tool to install. JOE

User Avatar

Chevy Lumina has not the carborator.

User Avatar

The alternator on a 95 Chevy Lumina 3.4l is replaced by disconnecting the wiring harness, loosening the retaining bolts, and removing the serpentine belt. The alternator can then be unbolted, removed, and a new alternator installed.

User Avatar

on the front of the engine on the serpentine belt, it's bolted directly to the engine.

User Avatar

In the drivers manual if pulley has grooves belt grooves face it if pulley is slick back of belt faces it

User Avatar

Any place that sells batteries can tell you the correct size battery. The AC/Delco battery is one of the best.

User Avatar

Where is the computer on a 95 Chevy lumina

User Avatar

First and foremost, make sure you have a diagram before removing the old belt. If there isn


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.