First install the c-clip back into the handle then push the handle on to the pin, it will snap into place.
It won't snap into place that easily. You will have to give it a good rap with the palm of your hand or even better a rubber mallet.
There is a spring clip that holds it on. Take a paperclip and bend the end about 1/8 inch at a right angle. Press the door panel in and you will see the clip on the backside of the door handle. One end is looped. slip the paperclip into the loop and pull. The retaining clip will slide out and the door handle will come off. To put the handle back on just. put the clip back in the slot on the handle and press it onto the shaft.
you can go to any auto parts store and buy a clip removal tool to remove handle. this tool will remove the c clip so you can remove handle. heres another way, but it takes longer. put a clean rag between door and back of handie, move the rag back and forth. when the rag makes contact with the clip, it should pop it off or far enough to remove handle. to put handle back on door. push the clip on the handle and push handle back on door good-day !
there is aq clip whivh is located on the rod going from the door handle to the door latch just find the clip and put back in is broken like mine i made a clip and it has not broke since.
There is a small retaining clip behind the handle. Just take a small flat-tip screwdriver or equivilent and push the clip off the slot behind the handle. By using your finger to push against the door panel right next to the handle, you will be able to see behind the handle and see the clip. The clip resembles a "c" with the ends bent up. Once the clip is removed, just pull on the handle and it will slide off the shaft. When you install the handle, just put the clip into the slot on the handle and gently push the handle back on the shaft. When you hear it snap into place, it is now locked back into position.
If you push the door panel in and look behind the handle you will see a small clip push it off with a small screw driver. It will be a little tricky but it will come off. When you get ready to put handle back on you will need to put the clip in the handle groove first then push the handle onto the shaft.
It is not that hard... all you have to do is when you have the new door handle you have to take the door panel off on the inside of the car and reach through the holes and unscrew the bolts to the handle and the door handle should come off and put the new one on and put the screws back on and put the door panel back on. It is not that hard... all you have to do is when you have the new door handle you have to take the door panel off on the inside of the car and reach through the holes and unscrew the bolts to the handle and the door handle should come off and put the new one on and put the screws back on and put the door panel back on.
If the door handle is broke you need to replace it. But check if the rod came off. Sometimes the clip slides off and the rod comes off. Simply connect the rod back and put the clip back on to keep it in place
there is a small U shaped clip behind the handle pull gently on handle while pushing gently on door panel have a friend shine a flashlight between the opening you created and you will see the clip push clip off with equally on both sides with two small screwdrivers or you can purchase proper tool from auto parts store for about 5 bucks when you replace handle put clip back on handle first then simply push back on you may have to be slightly aggressive.
Push in on the door panel just at the handle knob and use a screwdriver to pop loose the retainer clip.The knob will slip right off. When you put it back on just insert the clip on the handle and push the handle back into place.
There is a clip behind the handle. You remove the clip and the handle comes off, just remember they are a bear to put back on with out the handle removal tool.
there is a clip on the back side of handle u will need a special tool for that just go to a local automotive shop im sure they will pop it off for u and u can just put the clip back on the handle and push it on ur self when ur done
You need a special tool. You can probably get it at Autozone. here is an other way!! use a clean rag and put in back of handle, move back and forth at clip , when cloth hits clip it will pop it off!