Electric Windows
Chevy Silverado
Chevy Suburban
Nissan 240SX

How do you remove-replace the window motor for a 1995 240sx?

626364

Top Answer
User Avatar
Wiki User
2015-03-11 20:12:17
2015-03-11 20:12:17

Window motor 1995 240sx Nissan.

Had trouble with my drivers side window motor 1995 Nissan 240 sx. Window button broke inside and constantly sent signal to amplifier (a clicking sound could be heard) and eventually burned out the window motor.You'll need a Phillips screwdriver, ratchet set, a very small flat end screwdriver to pry plugs apart a window chock or two and some plastic bags for screws, nuts and bolts and a marker to label bags as to where screws nut and bolts came from.Instructions on how to remove motor: Remove the screw vanity cover inside door handle well, unscrew. Remove door panel plug on top rear of panel. Unscrew three screws bottom of door panel. Unscrew door handle trim (slightly lift door handle for access. Remove door handle trim slowly or it will break. Remove button assembly and hand pull well by lifting up and taping non button side of well high (a metal clip holds the button assembly side in place.) Disconnect button assembly switch plug. Remove handle well and switch assembly. Remove door panel by prying away from front and back of door and then lifting up. Carefully store door panel (it fits in the back seat.) Remove speaker enclosure with speaker attached and disconnect speaker plug (4 screws hold white speaker enclosure to door.) Alternately you can hang speaker enclosure to door with piece of hanger. Depending on where the window is positioned there is one nut on each side of the bottom of window which attaches window to steel rail. There is an access hole for the front most window nut by the motor area. Use a rubber window chock or rubber door stop to keep window from falling when disconnecting window. Disconnect two screws on door which holds regulator slide bar. Remove 4 bolts which hold window motor assembly to door. Disconnect motor plug from line leading from the amplifier (white rectangular box on door.)Motor and regulator will slide through the cutout on the bottom left side of door.The motor is expensive so if you can find one on e-bay you might save a great deal of money. Motor from dealer $300, button assembly $250 amplifier $75. Retrace steps for reassembly. I had to repeat the assembly process a couple of times until I determined that my problem was both a broken window button and a bad motor. I repaired the button with some plastic weld bonding material and a small piece of steel to reinforce the interior of the button. You can't buy just the buttons from the dealer.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Yes. The ka24de motor is used from 95 through 98.not just used from 95 to 98 because i have a 1990 240sx with a ka24de in it

User Avatar

Yes, some '92 240sx' came with the ka24de motor.

User Avatar

I need instructions on how to change the window motor in 1995 Chevy Camaro.

User Avatar

Is a 1995 Nissian 240SX Engine compatible to 1992 Nissian 240SX?

User Avatar

they are in the doors. the regulator is what makes it go up and down and is attached to the window motor.

User Avatar

you must determine weather the switch or window motor is bad and replace.

User Avatar

check the following; fuses, relays, regulator, window motor, off track, window switch. did not specify if it was manual or electric.

User Avatar

The 1995 Cadillac Eldorado drivers side door panel is held in place by eight retaining clips. Pry outward on each retaining clip. The door panel will come off. Remove the linkage from the power window motor. Remove the wiring harness from the power window motor. Remove the retaining bolts. Reverse the process to install the new power window motor.

User Avatar

I believe for yours it is 5x114.3. As for the 1989-1996 240sx is a 15x6 wheel with 4x114.3 or as for the 1995-1696 240sx se is a 16x5.5 wheel with a 5x114.3. Reference: http://www.discountedwheelwarehouse.com/Nissan___Vehicle_Bolt_Pattern_Reference.cfm

User Avatar

if they are both turbod then yes, no if they aren't the manifolds are different

User Avatar

Its on the passenger side of the motor. Its kinda hard to see and get to but it should be right below or next to the alternator. Try following the positive battery cable.

User Avatar

You can remove the door panel. And there are 3 star bolts that hold the power window motor. Once you remove the motor you can remove gear cable from motor and pull up the window by hand. That is the only way I know of. I had two motorcables brake on me.

User Avatar

You have to remove the door panel and anything else like door pulls and window handles.

User Avatar

1989-1990 240sx 1990-1997 Hard body 1990-1995 Pathfinder 1989-1995 Axxess 1990-1992 Stanza They are all the same engine.

User Avatar

You don't let some else do it. I say this from experience on a 2004 The motor is separate I used the old motor and replaced the regulator. I had to drill out rivets OH ya I BROKE the window drilling out the rivets that hold the window onto the regulator. after that I reattached the motor assembly with bolts and nylon lock nuts. then went to a glass shop to have the window replaced.

User Avatar

The signal flasher on a 1995 240SX is under the dash on the driver's side. Look for a small three-prong plug in.

User Avatar

the motor is loose on it's mount and it's gear is not engaging the window roller or the gear in the motor is loose or broken from the motor shaft. The window regulater is broken. You will need a new one. cost about 50.00 for parts and about that if you have it installed. glass speciality or a similar business can do it faster and without any problems.

User Avatar

Hi .. To change the power window motor .. Remove the door shell of course You will see the motor for the window .. Unplug the power of course . The motor is actually riveted in so you need to drill out the rivets. Remove the old unit . Then install the new motor with self tapping screws . Plug in the power . Be sure to secure the window when you remove the motor so it doesn't fall. I have not done this yet but am about to embark soon and have done some research . Good luck ..

User Avatar

The window motor drives a cable witch is routed around a couple of pulleys. The cable may have come off of one of the pulleys or the cable may have broken. The repair is very involved and should not be tried by anyone not familiar with window regulators.

User Avatar

There could be several causes for this type of problem: 1) The power window up portion of the switch is not functioning or wiring is loose at the switch and or motor. 2) The motor is failing and is not providing enough force to raise the window or is off-track and inding. To check this condition lower the window , then grasp the window and when the up button is pressed assist it(leave enough space to ensure you do not pinch you hand.in the window frame) if the window motor operates and the window begins to rise the window could be binding or the motor replaced. in either case the door panel will need to be removed the electrical switch and motor are tested and the mechanical operator and track inspected for proper operation.

User Avatar

loosen the manual tensioners and the alt bracket.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.