you should actually have a serpentene belt, which runs every accessory there should also be a belt tensioner located just below your alternator, on the tensioner ther will be a square hole. place a 3/8" drive ratchet into the hole(make sure the ratchet is set to loosen not tighten. with the ratchet take tension off of the belt and remove it, and do the same thing to replace it, you made need to remove your fan shroud to gain comfortable access. good luck
Remove the wiring harness or the fan motor belt, depending on the year of your Chevy Cavalier. Remove the fan motor retaining bolts. The fan motor will come off.
REMOVE THE SINGLE DRIVE BELT, THEN REMOVE THE 4 MOUNTING BOLTS BETWEEN THE FAN AND THE BELT PULLEY. THE FAN MIGHT NEED TO BE WIGGLED OFF
pull on your tensioner to remove pressure with a wrench remove belt and reverse
i will find out 4 u my dads a mechanic
Drain the radiator. Remove the fan and fan shroud if needed. Remove the pump belt. Unbolt the pump and remove it. Install the new pump. Reinstall the belt, fan and fan shroud. Refill the system with new coolant.
Drain the radiator. Remove the pump belt. Remove the fan and shroud if needed. Unbolt the pump and remove it . Bolt on the new pump. Reinstall the fan and shroud, the belt, then refill the radiator.
Pull the radiator shroud, remove the serpentine belt, remove the fan from the water pump shaft, then remove the water pump.
loosen the four nuts that hold clutch fan to water pump then remove serpentine belt then remove the loose nuts ,take fan from engine.
Put your new fan belt around the pulleys of your 1992 Chevy Blazer. Tighten the fan belt with the tensioner pulley.
how do you change a fan switch on a 1997 Chevy cavalira
how do you replace fan belt on 95 Chevy S-10 2.2 engine
remove the old belt and remove your trouser's belt off and put into the fan
you have to take the fan off the water pump then remove the water pump and you will see the timing belt cover it looks kind of like and oval shape you have to remove that cover and there youll have it A 95 Chevy has a timing chain not belt!
a picture of how to assemble a fan belt fro 98 Chevy venture van
Drain the radiator. Remove the pump belt. Remove the fan and shroud if needed. unbolt the pump and replace it with the new one. Reinstall the fan, shroud, and belt. Fill the radiator with coolant.
remove your fan shroud then losen the tensioner and remove your belt.
Remove the 4 nuts that are against the pulley behind the fan with the belt still on the truck. Once these nuts are removed, the fan will separate from the pulley. Now you can remove the belt & water pump pulley.
how do you change a ac fan switch on a 1997 Chevy cavalier
remove upper fan shroud, unbolt fan from water pump, remove belt, remove hoses from water pump, remove water pump bolts, transfer heater hose fitting to new waterpump, clean up old gasket, install in reverse order.
Drain down the radiator using a large clean drain pan. Remove top half of fan shroud. Remove accessory drive belt. Remove fan assembly. Remove water pump pulley. Remove lower half of fan shroud. Remove water pump. Clean gasket surface area. Install in reverse order. Not knowing what engine you have this is a general answer.
how to change the fan belt on a 1995 Chevy blazer vortec motor?
the 1997 camaro doe's not have a fan belt it has a serpentine belt that you can change in about 5 min.
If it is a serpentine belt you replace the tensioner pulley
Before you remove the old one, make a sketch of how it is routed. The diagram is located on the hood above the belt.
Remove fan clutch with fan impeller. Remove A/C compressor drive belt. Remove cap from tensioning roller. Relieve tension on drive belt. Remove drive belt. Reverse procedure for installation.