0
You do not need to remove the manifold.
Before starting get only Ford wires and spark plugs.
Mazda or Ford dealership will have the stuff. Replace both together.
Use dielectric grease as well and gap the plugs correctly.
For the 2001 you will need to know your VIN, as they changed the coilpack midflight, so there are two types of wires. One has clips,and the other just a push on.
You will need some socket extensions and a spark plug socket with rubber catch inside.
Step 1. Remove IMRC module 3 10mm bolts, move carefully to the side.
It is a rectangular box low right side with 3 bolts.
The front 3 plugs (cyl 4,5,6) is now exposed to replace.
Step2.
The rear plugs look hard, but not so bad.
Unclip the coil pack wire. Depending what kind of coil pack you have there will be 3 or 4 bolts. 4 bolts if you have clip on wires, or 3 if you do not (2 on the left side, 1 center on the right). I think they are 7mm, can't remember.
You will need a short extension. You will be working a little blind, but it is not so bad. Point a flashlight in there. Pay attention to the ground strap on the right hand side, it comes off one of the bolts when you unbolt the coil pack. Once you get the coil pack out of the way it easier to get the plugs.
Use a long and short extension combination for the rear plugs (1,2,3). Once again you are working blind, but it is not hard at all.
You cannot use the sparkplug socket to put the plugs back in as the rubber inside will keep you from getting your socket out.
I use a rubber hose over a plug to drop the plug in and start the threading, then I use a regular 5/16th socket to tighten. Use some anti siege on the threads. Do not over tighten.
Pay close attention to the numbering on the coilpack. It is marked on the coilplug, otherwise you will screw up.
Put the coilpack back in. Remember the ground wire on the right, and some other gizmo on the left when placing the bolts back in.
Install the new wires. Trasnfer the wireloom from the old wires to the new wires (only if original wires, you mat not have a wire loom).
It is not so bad. Most of time is just fidling around with extensions.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the correct spark plug gap on a 2001 Mazda Protege 2.0?
.044
How do you change plug in 2001 Mercury Grand Marquis?
Remove the spark plug wire from your 2001 Mercury Grand Marquis. Remove the spark plug with a 5/8 deep well socket, white turning it to the left. Reverse the process to put in the new spark plug.
What is the spark plug gap needed for a 2001 Mazda 323 1.6l engine?
1.00-1.10mm
How do you change spark plugs on a 2001 Crown Victoria?
Remove the coil on top of the plug, then just remove the plug.
How do you change spark plug on a mazda tribute 2004?
Disconnect the battery, remove the intake manifold, remove the spark plug boot covers and cables, and remove the old spark plugs. Put in the new spark plugs, attach the spark plug boot covers and cables, replace the intake manifold and connect the battery.
What is the spark plug gap for a Mazda Tribute 2004 V6 2WD?
what is spark plug for mazda tribute 2004
How do you replace spark plugs 2001 stratus rt?
Disconnect the battery, remove the spark plug cables, and remove the old spark plugs. Put in the new spark plugs, attached the spark plug cables, and connect the battery.
What is the spark plug gap on a Mazda b2300?
What's the spark plug gap for 2003 Mazda 2300 pic up ?
How do you remove the spark plugs from a 2001 Mercury Grande Marquis?
You should have C.O.P. ( coil on plug ). Just remove the coil, and remove the plug the normal way.
What is the spark plug gap on a 2002 Mazda 626?
The spark plug gap on a 2002 Mazda 626 should be set at .044 inches. A new spark plug will come preset from the factory.
What are the spark plug gap specifications for a 1998 Mazda B2500?
It is important to remember the spark plug gap when changing the spark plugs of a vehicle. A 1998 Mazda B2500 has a spark plug gap of 0.042 to 0.046 inches.
How do you get to number 3 spark plug on a 2001 ford escape?
Remove the intake manifold.
