0
Under the index button there shold be a screw , loosen the screw and take off the handle
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you fix a leaky faucet?
Fixing a leaky faucet is often a simple matter of replacing the rubber seat and the packing. (Note: This does not apply to ball type faucets.) * Turn off water to the faucet at the valve under the sink. * Open the faucet and make sure the water is actually off. * Remove the handle. This varies from faucet to faucet, but most often there is a screw under a cap. * After removing the handle you should see a nut around the shaft of the valve. Remove this nut. * Remove as much of the old packing that was between the shaft and the nut as you can. * Using the handle, unscrew the valve core from the body of the faucet. Turn it in the direction you would to turn the faucet on. * At the bottom of the valve core you removed should be a rubber seat held in by a screw. Remove this. * Take the valve core and rubber seat to the hardware store to get a new rubber piece. Also get new packing. Without packing the faucet will leak under the handle. The old packing cannot be re-used. * Assemble the new rubber seat into the valve core. * Clean any old packing off the valve core and the nut. * Screw the valve core back into the faucet body. * Wrap a few turns of packing onto the valve body. Hand tighen the nut back on. * Do not install the handle yet. * Carefully turn the water back on. You should be able to turn the water fully on and off. If the faucet leaks at the valve stem, tighten the nut until it stops. Do not overtighten the nut as it will make it difficult to remove later and will make the faucet handle stiff. * Re-attach the handle. There are many different kinds of faucets or taps. This might apply to yours. *Turn off the main stopcock so the water won't pour out when you remove the tap/faucet. *Start with the top. Is there a little nut or screw you can remove to separate the handle? If there is you can remove that. You might have to hit the handle upwards or outwards with the handle of a hammer. Try not to damage anything. Even if you can't get the handle off, you might still be able to continue below. *You should then be able to unscrew something. It might just be a cover. You might need a stilson wrench for this. Sometimes the cover is on a spring that you can pull forward to expose the nut behind. *Then there might be a nut to unscrew which will remove the whole front of the faucet or tap. You WILL need a wrench or shifting spanner for this. *Pull out the valve with your fingers. If it is worn and leaking, you should replace it. A worn valve is the most common problem with leaking taps. *Then put everything back. Unless you are throwing away the old faucet/tap and replacing it with a new one. *Make sure you can turn the front handle before you tighten up the back nut. *Turn on the main stopcock. *Clean up all the dirt and muddy water from the floor. *Take a shower to test it before you tell everyone else of your magnificent achievement. turn off the water.. OR! better yet.. call a plumber Replace it. Replace it. That's easy. You need to replace the faucet washer. it's fairly simple to do, just make sure you turn off the water under the sink before you start taking the faucet off. Any knowledgeable hardware store employee should be able to assist you. Replace the rubber washer inside the faucet.To do this you must turn off the water to the faucet; usually this means turn off the city water supply to the house.Remove the handle, expose and remove the old washer.Take both to plumbing supply and obtain replacement washer if none on hand. Install and then turn on the water.turn water off at sink, remove hoses, remove nuts under sink [on faucet]remove faucet, clean area, replace with new one,[don,t forget to put rubber gasket under it] install new nuts, tightenattach water lines, turn water back on. go to lowes or home depot and have someone in the plumbing dept.walk you thru the process and then decide if you really want to try it on your own. its not rocket science but its not easy for the average joe either. I could describe it all for you but the above method is way better for you!! check the washer or the o ring, it may need replacing == Answer== Any faucet is easy to fix if you have the right tools, parts and can get the faucet apart. It is not always easy to have all of the above. I would call a plumber. unscrew it or pull off. You can tell the difference if it has a lock screw under the faucet. Pay attention to sealant. When replacing make sure the pipe is the correct length and size for your replacement faucet.
How do you repair a faucet stem leak?
With the faucet shut off, take the handle off and under it is a nut around the stem. There is either an O ring under the nut, a fiber washer or stem packing depending on what type of faucet it is. Replace which ever it has and that should fix it. If your faucet is a screw type, the handle turns several time when opening it, you can probably take the nut off, wrap two or three wraps of stem packing around the stem, clockwise looking down on it and replace the nut and tighten. This will compress the packing around the stem without replacing the cone washer in the nut or all of the old packing.
How do you replace a faucet valve?
You dismantle the faucet and take the seal, 'o' ring or cartridge to hardware store to get an identical item. Then re-build it in reverse order. In some the @o@ ring does not exist. Therefore you will need to replace the whole faucet gland. To do this again stop the water the the faucet, remove the facuet and check the type you have. If its integrated then you are advised to take this with you to the DIY (plumbing) supplier to check thread size and which hand (left or right, hot or cold) needs replacement. Most cost about 7$ (5£ uk)
How do you change a stem valve for a price pfister faucet 2 handle type?
I'm assuming you have a some kind of a leak. The problem is usually caused by something called a seat. It looks like a washer; but, it's not. Because it has a square access You might need to purchase a "Faucet Valve Seat Wrench". It looks like the letter L Most hardware places will carry one. I got mine at Home Depot's. I will add more to this later. It took me months to figure what those extra washers were that came with the valve stems were. They didn't include instructions or anything.
What are the two types of bearings used in motors?
ball type
What mechanical principle is followed by the single handle faucets?
In a single handle faucet the mechanical principle is a ball valve one. This is where the ball valve acts to cut off whichever type of water is not wanted so the correct water comes out.
How do you remove faucet handle from a moen bathroom sink faucet 4510?
The cap does NOT come off. It is all part of the handle. To take the whole handle off, there is a set screw at the back that can be undone with an allen key. The older discontinued models, the cap can be pried off with a small screwdriver.
How do you remove and replace a shower faucet?
Depends on the type already installed
When I completely close my shower faucet the water still runs so to actually shut off the water I need to open the faucet a little bit What is going on?
What type of faucet is it? Is it two taps, or one, Twist to turn on/off, or push/pull? It is a one handle, twist on/off type faucet.
Vessel Faucet Difference?
A vessel faucet is a type of faucet. Many restaurants use this style as it is very elegant, with large handle hooks and fairly inexpensive. A vessel faucet produces a great water flow and can make anyones bathroom look great
How do you fix a valve on a bathtub tap that switches from bath to shower?
It will depend on the type of faucet if it is a three handle or has a popup in the spout popup in the spout will be the easiest to repair do so just by replacing with a new spout if it is a three handle you will have toremove the center handle and then remove the stem there will be a washer of some type replace the washer and put back together and try.
Shower Faucet ?
form_title= Shower Faucet form_header= Install the shower faucet you want in your bathroom! Do you have a working faucet in your bathroom?*= () Yes () No () Not Sure What type of faucet do you want installed?*= _ [50] Do you want the shower faucet to include a massager?*= () Yes () No () Not Sure
Bathrooom faucets drip. How do we repair or replace?
If the faucet is the quarter turn or single handle type, you put new seal in it. There is some variance in how they come apart but here's the basics. Shut the water off. Remove the handle. Dual handle are held on with a screw through the top. Remove the hot/cold cap and the screw is under that. There will be a nut under that holding the stem in the faucet. Remove the nut and the stem will pull straight up and out. In the resulting hole you will see a small black seal, the size of a pencil erasure. This comes straight out. There is a small spring under the seal. Replacement seals usually come with a new spring. replace in reverse order and drip is fixed. The stem should only go in one way, usually a small tit that locates it. Single handle is basicly the same process. Handle is held on with a set screw, there may be a cover plate over it if it is on the front of the handle. Remove handle, bigger nut under it, larger ball under that and two of the rubber seals. Same process in replacing.
How do you adjust a Delta tub faucet when they say that minor adjustments to the handle allow you to regulate the temperature of Ball-type faucets?
Take off handle and you will see how to do it. Be carefull not to let the parts fall off the stem. If they do you could go to Lowe's and ask how to put it back together. Just take the parts with you. This is for a pressure balance Delta.
How do you replace a pull out hose a faucets?
It connects to the faucet under the sink. Depending on the manufacturer, it may screw on, have a hairpin clip holding in it or push into the faucet. You remove the last type by pushing the hose in just slightly and holding it there then push in the ring around the base of the hose into the faucet and pulling the hose out. To replace this type, just push it into the faucet till it bottoms out.
How do you fix a leaky faucet?
Fixing a leaky faucet is often a simple matter of replacing the rubber seat and the packing. (Note: This does not apply to ball type faucets.) * Turn off water to the faucet at the valve under the sink. * Open the faucet and make sure the water is actually off. * Remove the handle. This varies from faucet to faucet, but most often there is a screw under a cap. * After removing the handle you should see a nut around the shaft of the valve. Remove this nut. * Remove as much of the old packing that was between the shaft and the nut as you can. * Using the handle, unscrew the valve core from the body of the faucet. Turn it in the direction you would to turn the faucet on. * At the bottom of the valve core you removed should be a rubber seat held in by a screw. Remove this. * Take the valve core and rubber seat to the hardware store to get a new rubber piece. Also get new packing. Without packing the faucet will leak under the handle. The old packing cannot be re-used. * Assemble the new rubber seat into the valve core. * Clean any old packing off the valve core and the nut. * Screw the valve core back into the faucet body. * Wrap a few turns of packing onto the valve body. Hand tighen the nut back on. * Do not install the handle yet. * Carefully turn the water back on. You should be able to turn the water fully on and off. If the faucet leaks at the valve stem, tighten the nut until it stops. Do not overtighten the nut as it will make it difficult to remove later and will make the faucet handle stiff. * Re-attach the handle. There are many different kinds of faucets or taps. This might apply to yours. *Turn off the main stopcock so the water won't pour out when you remove the tap/faucet. *Start with the top. Is there a little nut or screw you can remove to separate the handle? If there is you can remove that. You might have to hit the handle upwards or outwards with the handle of a hammer. Try not to damage anything. Even if you can't get the handle off, you might still be able to continue below. *You should then be able to unscrew something. It might just be a cover. You might need a stilson wrench for this. Sometimes the cover is on a spring that you can pull forward to expose the nut behind. *Then there might be a nut to unscrew which will remove the whole front of the faucet or tap. You WILL need a wrench or shifting spanner for this. *Pull out the valve with your fingers. If it is worn and leaking, you should replace it. A worn valve is the most common problem with leaking taps. *Then put everything back. Unless you are throwing away the old faucet/tap and replacing it with a new one. *Make sure you can turn the front handle before you tighten up the back nut. *Turn on the main stopcock. *Clean up all the dirt and muddy water from the floor. *Take a shower to test it before you tell everyone else of your magnificent achievement. turn off the water.. OR! better yet.. call a plumber Replace it. Replace it. That's easy. You need to replace the faucet washer. it's fairly simple to do, just make sure you turn off the water under the sink before you start taking the faucet off. Any knowledgeable hardware store employee should be able to assist you. Replace the rubber washer inside the faucet.To do this you must turn off the water to the faucet; usually this means turn off the city water supply to the house.Remove the handle, expose and remove the old washer.Take both to plumbing supply and obtain replacement washer if none on hand. Install and then turn on the water.turn water off at sink, remove hoses, remove nuts under sink [on faucet]remove faucet, clean area, replace with new one,[don,t forget to put rubber gasket under it] install new nuts, tightenattach water lines, turn water back on. go to lowes or home depot and have someone in the plumbing dept.walk you thru the process and then decide if you really want to try it on your own. its not rocket science but its not easy for the average joe either. I could describe it all for you but the above method is way better for you!! check the washer or the o ring, it may need replacing == Answer== Any faucet is easy to fix if you have the right tools, parts and can get the faucet apart. It is not always easy to have all of the above. I would call a plumber. unscrew it or pull off. You can tell the difference if it has a lock screw under the faucet. Pay attention to sealant. When replacing make sure the pipe is the correct length and size for your replacement faucet.
How do you you remove a shower faucet handle that is stuck with calcium buildup?
As with any answer...it depends, but try this: If the faucet is the single handle type, use an Allen wrench to remove the small set screw from the handle, (if the handle set screw has too much mineral build up, wrap the handle to include the set screw with a paper towel. Secure it with a rubber band; and then soak with vinegar and leave it for several hours) "Break" the seal of the set screw using the Allen wrench, and remove the handle.The remaining parts, under the handle, will probably have the same problem. Use the same process. At this point turn off the valves leading to the fixture (you may have to turn off the water at the meter) Continue dismantling, use the correct and appropriately sized tools. This should help but if your faucets have been neglected for a long time, probably plan to replace the faucets.Hope this helps...
