0
How do you remove a dent from a Toyota corrolla drivers side door?
Wiki User
∙ 11y ago
Depending on how large it is and if the metal is creased or not, you can simply remove the dent by using s large suction cup and pull it out. If there is an actual crease in the dent, then other methods would have to be used.. Tapping it out from the inside by removing the inner door panel then shaping and finally filling and repainting. OR you could call a local Paintless dent repair company and let them decide the best way. Good Luck.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you repair your dents auto?
It depends on the size + type of the dent. If the dent doesn't have a distinct crease it can be popped out many times with a suction cup, tapping around the outside edges. If it is a more serious dent, it will probably be necessary to get behind the dent and pick it out. Sometimes you can make a small hole in the side or bottom of the panel and pick it out with a pry bar, filling the hole with a plug when finished.
How do you find your weight on another planet?
i dent know
How do you remove a 1.5 inch by 2 feet vertical dent from a steel garage door?
the same way it was made (with pressure) get someone to hold a piece of wood at one side while you tap the other side with a hammer. thhe damage has already been done so you can only make it better hope that helps :)
Does Harvey Dent die in the dark knight?
Any characters death in a film, book, video game can obviously be argued until the end of time. But logicially, Harvey Dent/Two Face protrayed by actor Aaron Eckhart died. Batman fell from the same height that Two Face did, yes--but, mind you Batman's suit is out fitted with Kevlar bullet proof platting and earlier in the film Batman jumps from over four stories up onto Scarecrow's van and the fall doesn't phase him in the least bit. Comparing a fall between a lawyer in a half-burnt suit and a trained Martial Artist wearing one of the greatest built combat suits ever made doesn't hold water. Batman's fall was also broken by several boards, and he in fact fell from a lesser height -- he was hanging from floor joists, dangling from his arm, thus shortening the distance by at least a good eight feet. Dent fell backward, Batman dropped straight down, so they likely fell differently as well. Also, the idea of a man whose healing from a half burnt body getting up from a high fall and getting away, successfully when the entire area is swarming with cops is highly unlikely. Also, Gordon was near enough to Harvey Dent's body to keep an eye on it, highly unlikely again that Gordon would not notice Harvey getting up and running off. In fact, Gordon and Batman stand over Harvey Dent's body without attempting to provide even basic medical assistance or to call for emergency help (Gordon finally "calls it in" when Batman tells him to do so, several minutes after they've discussed the situation). Batman makes his speech about dying a hero or living long enough to see yourself become the villain. Dent died, Batman lived. Dent will be branded a hero, Batman will accept the role of villain. This is a long-running notion throughout the film, and it culminates in Batman's decision to let Dent die a hero in the eyes of Gotham City. The shooting script for the film states that Harvey Dent is "DEAD" (in all-caps), and in interviews Chris Nolan and his screenwriting partner on the film, brother Jonathan Nolan, have both said Harvey Dent was killed in the film. Arron Ekhart has stated repeatedly in interviews that his character died, including referencing Chris Nolan telling him on the set that his character was gone and would not return (at least in life). Now, it's completely a fair argument to say that it is "possible" and to discuss that Two Face lived. But to say A HUNDRED PERCENT that he didn't die when there's more than a fair amount of evidence that he did die...No. Lastly, it hasn't been stated ANYWHERE OFFICIALLY, that Two-Face is the focus of next film. Chris Nolan has recently announced that he is working with his screenwriting brother (who co-authored the script for "The Dark Knight" with Chris Nolan) to develop a story for the next Batman film. While Nolan still has not officially committed to the project, there is already much going on behind the scenes, and every indication is that he will return. However, his only comments about Harvey Dent that even come close to implying a "return" for the character actually suggest that perhaps Dent will return in flash-backs, to clarify the question of who exactly Dent killed in "The Dark Knight". At the end, Gordon says there are "Five dead, two of them cops", but the film only shows at most four of Dent's killings, and only one of them is a cop. However, what Gordon says is "Five dead, two of them cops. You can't sweep that under the carpet." He may have been including Harvey Dent (a DA, or "cop" to the average layman) himself in the equation, pointing out that along with the killings that Dent committed it would also be difficult to sweep Dent's own presence and death at the hostage situation under the carpet without having someone else to blame for the other murders (Batman). If we take for granted that Dent kills the henchman of Maroni's that he pulls off screen, then the number is correct (Maroni's henchman, Maroni's driver, Maroni, Wuertz, Dent). This being the case, it is five deaths that Gordon is worrying about covering up, not specifically five murders or five people Dent himself has killed.
A car made a dent and a small hole in the backdoor of a 2005 Corolla. Does the whole door have to be replaced or is it fixable And what is a price estimate?
Bring to body shop for estimate
Removing dents from rear bumper of Toyota Avalon?
Remove the bumper cover (mounted using a combination of snaps & bolts). Apply a force to each dent in the opposite direction of the force causing the dent. The dent area will often pop back into its original position.
Dent Removal?
form_title=Dent Removal form_header=Dent removal specialists can remove dents, dings, and hail damage on your vehicle without affecting the original finish. What is the year, make and model of your vehicle?=_ What caused the dent?=_ Where on the vehicle is the dent located?=_ Would you like the dent repainted?= () Yes () No () Not Sure
How do you remove the rear bumper cover on a 2004 Nissan Murano?
I have a small dent need to remove it
Can any average person remove a auto dent with no experience or should you take it to a bodyshop?
If the dent is not cressed an average joe can remove the dent by purchasing an easy out dent remover. They are pretty simple to use and the instructions make it pretty basic for any average joe to figure out. However it the dent has a wrinkle or creace in it, it would be much wiser to seek out professional help, that what they are trained to do. Some tasks are not ment for the average person to do themselves bodyshops are trained and have had schooling to master removing and refinishing a dent. If the dent is small yes if the dent is not and is creased seek out a professional.
How do you bump out a dent over rear wheel well?
There are 2 different ways to remove a dent over the rear wheel well of a vehicle. You can either suction the dent out from the outside of the wheel well or get the dent out by hitting the inside of the wheel well.
How do you remove radio from 2002 Lexus gs300?
Sledge hammer and a dent puller.
How can i remove a dent in my car without having to go to a car shop?
Compressed air can remove a dent in a car very quickly, Youtube has videos of how this can be done. Another way is to apply dry ice which is a very inexpensive alternative.
How does one remove a dent in the car?
Dents in a car can be removed by seeing a specialist, or can be done at home. If you want to remove a dent at home, the best ways to do it could be the hair dryer and dry ice method, or by using a tool such as the Pops a Dent, which is basically a strong magnet which can pull the dented metal back to its original shape.
What is the best way to remove a dent from a car?
There are a number of easy do-it-yourself ways to repair a dent that have worked for people. The best method largely depends on the type of dent. One way is to use dry ice or a hair drier on the dent. This can remove small dents. Another way is to use a toilet plunger to pull out a dent. A third way is to take a hammer to the inside of a dent and gently tap it out. When using any of these methods, one must inspect for paint damage and repair that as well with some matching touch up auto paint. Otherwise, the paint damaged spots can begin to rust.
What is the best way to remove a dent from a table tennis ball?
Put it in warm/hot water. I have done this before. The heat cause the air inside to expand and pop it out. The dent will pop out, but the surface still has a slight imperfection from the dent. It won't be as good as original.
Dented oil pan in 93 Chevy Corsica?
if you have no leaks it is not a big deal to have a dent. if the dent is huge it may cause inacurate readings on your dipstick, you could remove the pan and place it on a flat surface and work the dent out slowly but this could weaken the metal for the pan.
Explain why placing dented table tennis ball in boiling water is one way to remove the dent in the ball?
The hot water cause the air inside the ball to expand and push out the dent.
