Grip the nut with a pair of pliers and rotate in a counter clockwise direction.
Remove the door panel. Remove the switch retainer. Remove the wiring harness. Reverse the process to install the new switch.
Remove the wiring harness from the 2003 Jeep Liberty pressure switch. Remove the power steering pressure switch retaining screws. Reverse the process to install the new power steering pressure switch.
Remove switch panel and jump wires on switch- if this works bad switch Remove door panel and see if the motor is getting power-if it is getting power, bad motor
remove door panel check to see if you are getting power and ground to motor. If so, bad motor--if no power to motor, check to see if you have power to switch if so ,bad switch--if not bad power feed to switch close but if the switch not on, you never get power to the motor.
To remove a pressure switch in the power steering Au Falcon the proper tools must be obtained to take the piece apart. The proper instructions must also be obtained.
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door
remove the door panel then remove the switch which is secured at one closest to the front end by a Philips screw into a gold retainer
remove switch from where it is mounted using a wire , bridge the connections.if switch is bad, it will work the motor while bridged
The power steering pressure switch screws in. Simply unplug the wire harness, unscrew the old switch and screw in the new switch. Plug the wiring harness back in.
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door