0
How do you remove and install a steering shaft on a 2006 Pontiac GTO?
Wiki User
∙ 13y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How can you remove the left spark plug on a 2001 Chevy s-10 v-6 engine when it is blocked by the steering column?
Move the steering shaft. There is one bolt under the plastic cover. This is the pinch bolt .Remove it and slide shaft towards firewall ,move shaft out of the way ,replace plug,re-install shaft,bolt and plastic cover.
How do you replace the steering column shaft coupler on a 1998 Dakota?
1. Position the front wheels straight ahead. Place a steering wheel holder, SNAP-ON TOOL, p/n WA96A, or equivalent, between the steering wheel and the driver's seat to secure the wheel. 2. Remove the toe plate nuts (Figure 1). 3. Remove the pinch bolt and nut securing the upper intermediate shaft to steering column. 4. Open the hood of the vehicle and remove the pinch bolt securing the lower intermediate shaft to the steering gear. 5. Compress the intermediate shaft and remove it from the vehicle. 6. Feed the new intermediate shaft, p/n 55351171AA, through the cowl panel and install it onto the shaft splines of the steering gear. Then, compress and/or lengthen the intermediate shaft enough to be able to install the shaft onto the lower end of the steering column. 7. Secure the intermediate shaft to the lower end of the steering column with a new pinch bolt, p/n 06504926AA, and nut, p/n 06101510, and tighten the nut to 49 Nm (36 ft. lbs.). 8. Secure the intermediate shaft to the steering gear with a new pinch bolt, p/n 06504926AA, and tighten the bolt to 49 Nm (36 ft. lbs.). 9. Install the toe plate onto the cowl panel studs. Tighten the toe plate nuts to 10 Nm (90 in. lbs.). 10. Remove the steering wheel holder from the steering wheel. Information removed from www.alldatapro.com
How do you take steering wheel off 1973 Plymouth?
Remove horn ring or button (twist to remove) Remove center bolt on steering wheel Mark location of wheel in relation to steering column shaft for proper re-install Get and attach a steering wheel puller Tighten nut on wheel puller until steering wheel "pops" off
How do you install the exhaust manifold on the drivers side in a 1999 gmc jimmy with the head installed?
1. Remove bolt (11mm) that attaches steering gearbox from lower steering column shaft 2. Slide lower steering column shaft until it detaches from steering box spline 3. Remove wheel 4. Remove steering box bolts attached to frame, inside of wheelwell and slightly lower it without removing any lines 5. Simple grab a hold of the lower steering column shaft a slide downwards until it detaches from upper shaft section (the lower steering column shaft is a press fit, two piece design) 6. Remove the water temperature sender and spark plugs from head. This will give you the additional clearance to lower the exhaust manifold into place from the top.
How do you fix the steering on a craftsman mower?
Remove the mower deck. Remove the phillips head screw at the end of the shaft underneath the mower. The releases your shaft from the bootom of mower. Remove steering wheel and remove shaft. Replace parts as needed.
How do you remove a steering wheel from a 1994 Mitsubishi 3000 gt?
To remove the steering wheel start by disconnecting the negative battery terminal to prevent accidental airbag deployment. Then remove the screws on the backside of the steering wheel to remove the airbag. Disconnect the airbag wiring connectors. Remove the steering column shaft nut and remove the steering wheel with a puller. Do not yank, hammer, pry the steering wheel off as this could result in steering shaft damage.
How do you remove steering shaft on 1997 Chevy venture?
Not an answerable question. Missing need option and specific identification of what steering shaft. There are at least three.
How do you remove the power steering pulley from a 1996 Pontiac Bonneville?
There is a specific tool for this operation. It is a power steering pump pulley puller. This grabs the groove in the end of the pulley and pushes the punp shaft away from the pulley. Available at your parts store.
Location of 1955 Pontiac brake master cylinder?
The brake master cylinder on a 1955 Pontiac is bolted to the frame rail under the steering shaft.
How do you connect the rack and pinion to the steering column in an 04 Pontiac Grand Prix?
The steering column is connect with a shaft that runs from rack and pinion to steering column. A short shaft sticks out of rack and pinion and is attached to shaft with 1 bolt that goes thru the coupler. Usally hid under a boot that goes around the shaft.
Why is there a squeaking noise when driving a Kubota rtv?
The squeak is caused by lack of lubrication to the steering bushing. Pull the steering wheel off. There is a rubber bushing that surrounds the steering shaft. Remove the bushing with a thin screwdriver. Once removed clean the bushing and shaft. Then add anti seize lube to the shaft and and bushing. Then use a 7/8 " deep socket to drive the bushing back into the steering housing. Clean and add anti seize lube to the bottom of the steering wheel . Then install the steering wheel.
How do you remove a 1963 nova steering gear box?
When removing steering box the steering wheel has to be removed steering shaft is not remove able it will have to slide down when steering box is removed ie then remove pit man arm and bolts from the frame
