answersLogoWhite

0


Best Answer

You will have to take off the door panel and unscrew two bolts from the inside. You might be able to do it with the window all the way up.You'll have to loosen the lower window guide. remember how it's set up before you loosen stuff and make sure you have a diagram of how all the different internal parts in the door go. You can get this from the dealer parts dept. usually.

User Avatar

Wiki User

โˆ™ 2006-04-24 21:19:20
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove and install exterior door handle on a 2001 Honda accord ex?
Write your answer...
Submit
Related questions

How do you remove and install exterior door handle on 97 driver side?

Door handle to what?


How do you replace the exterior door handle on a 1984 Chevy Caprice?

Remove the inside door panel from your 1984 Chevy Caprice. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new exterior door handle.


How do you install an exterior door handle on Jeep Cherokee?

To install an exterior door handle on a Cherokee Jeep, first remove the window crank handle and the three screws in the inner door trim panel. Second, remove the inner door panel from the door using a trim stick and take off the vapor barrier inside the door. Third, remove the nut on the rear of the door handle, position the exterior door handle, and secure in place.


How do you replace the exterior door handle on a 94 Chevy beretta?

Remove the inside door panel from your 1994 Chevrolet. Remove the linkage from the door handle. Remove the door handle retaining bolts. Reverse the process to install the new door handle.


How do you replace an exterior door handle on a 1988 Blazer S10?

You will need to remove the inside door panel of your 1988 Chevrolet Blazer S 10. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.


How to replace a 1993 Chevy blazer full size exterior door handle?

You will need to remove the inside door panel of your 1993 Chevrolet Blazer. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.


How do you remove the outside door handle from a 1997 Honda Accord?

you have to remove the lock clinder


How do you change the exterior door handle on 2003 corolla?

You remove it and replace it...


How do you install exterior door handle 2003 jeep wrangler?

remove the interior door panel and you can get at the door handle, disconnect the rod and loosen the clips that hold it against the door, the whole assembly will come right out.


How do you replace exterior door handle on a 2001 ford focus?

Remove the door panel.Remove the bolt from the inside of the door that holds the handle on.


How do you replace an exterior driver's side door handle on a 1998 Lincoln Mark VIII?

Disconnect positive battery cable, remove all the bolts and screws from the door panel, disconnect the electrical plugs and carefully remove the panel. Remove the two nuts that hold the handle on, remove the linkage and reverse procedure to install.


How do you remove a house door handle?

In order to remove a house door handle, you will need to take a screwdriver and remove the screws from the exterior of the door. Once the screws are removed, the handle should simply pop out.


How do you remove a rear exterior door handle on a 2014 ford fusion?

Did you figure it out


How do you remove the exterior door handle on a 2001 BMW X5?

Sorry I don't know


How do you remove the outer door handle on a ford freestyle?

Removal of Rear Door Latch is necessary first. Rear Door Latch Removal: All vehicles 1. Remove the rear door interior trim panel. 2. Remove the access hole watershield. 3. Reconnect the window regulator and window switch electrical connectors and position the front door window to access the glass clamp bolt. 4. Disconnect the window regulator and window switch electrical connectors. 5. Loosen the window glass clamp bolt. 6. Tape the window in the full up position, then lower the window regulator downward until it reaches the stops at the bottom of the regulator track. 7. Remove the interior door handle bolt. 8. Disconnect the rear door latch assembly electrical connector. 9. Rotate the push button rod downward and remove it from the rear door latch assembly. 10. Remove the 3 rear door latch assembly-to-rear door module bolts. 11. NOTE: Make sure that the interior door handle does not get scratched when it is passed through the rear door module. Remove the 8 bolts and position the rear door module aside. FIVE HUNDRED AND MONTEGO 12. Remove the tape and lower the window glass. 13. Remove the scrivet. 14. Remove the rear door glass run top bolt. 15. Remove the rear door glass run seal. 16. Carefully position the glass aside, then remove the rear door glass top run. ALL VEHICLES 17. Disconnect the exterior door handle actuating rod from the rear door latch. 18. Remove the 3 rear door latch bolts. 19. Remove the rear door latch assembly. 20. Remove the remote cable cover from the latch. 21. Disconnect the interior door handle actuating cable from the rear door latch. 22. Remove the rear door latch from the bracket. * If necessary, remove the door lock actuator and the door ajar switch. INSTALLATION ALL VEHICLES Note: If necessary, install the door ajar switch and the door lock actuator. 1. Install the rear door latch on the bracket. 2. Connect the interior door handle actuating cable to the rear door latch. 3. Install the remote cable cover on the latch. 4. Position the rear door latch assembly. 5. Install the 3 rear door latch bolts. * Tighten to 12Nm (9 lb-ft). 6. CAUTION: The exterior door handle and the door latch must be installed and tightened to specification before connecting the exterior door handle actuating rod with the yellow clip. CAUTION: The exterior door handle actuating rod must be hanging freely then clipped into the door latch. Loading the exterior door handle actuating rod up or down when connecting may result in a misadjustment of the latch causing the latch not to operate correctly. Connect the exterior door handle actuating rod to the rear door latch and close the yellow clip. FIVE HUNDRED AND MONTEGO 7. Install the rear door glass top run and carefully position the glass. 8. Install the rear door glass run seal. 9. Install the rear door glass run top bolt. 10. Install the scrivet. 11. Raise the window glass and tape it in the full up position. ALL VEHICLES 12. NOTE: Make sure that the interior door handle does not get scratched when it is passed through the rear door module. Position the rear door module and install the 8 bolts. * Tighten to 8 Nm (71 lb-in). 13. Install the 3 rear door latch assembly-to-rear door module bolts. * Tighten to 12 Nm (9lb-ft). 14. Install push button rod on the rear door latch assembly. 15. Connect the rear door latch assembly electrical connector. 16. Position the interior door handle and loosely install the bolt. 17. Untape the window glass, then lower the window glass. 18. Install the window glass clamp bolt, * Position the window in the window clamp. * Shift the door window glass fully forward. * Tighten to 8 Nm (71 lb-in). 19. Install the access hole watershield. 20. Install the rear door trim panel. 21. Center the inside door handle alignment pins to the rear door trim panel and install the interior door handle bolt. * Tighten to 7 Nm (62 lb-in). EXTERIOR REAR DOOR HANDLE REMOVAL: Remove: 1. Remove the rear door latch. 2. CAUTION: Hold the bezel cap when removing the bolt or damage to the door may occur. Using a T-5 torx socket installed on the bolt tip, loosen the bezel cap bolt until the bezel cap can be removed. 3. Shift the exterior door handle rearward and remove the exterior door handle. 4. Remove the exterior door handle gasket. 5. Loosen the exterior door handle reinforcement bolt. 6. Remove the exterior door handle reinforcement from inside the door. 7. Release the bezel cap from the bezel and remove the bezel cap bolt. INSTALLATION 1. Install the exterior door handle reinforcement on inside the door. 2. Tighten the exterior door handle reinforcement bolt. * Tighten to 7 Nm (62 lb-in). 3. Install the exterior door handle gasket. 4. Install the exterior door handle. 5. Install the bezel and the bezel cap bolt. * Tighten to 12 Nm (9 lb-ft). 6. Position the exterior door handle forward. 7. Snap the bezel cap on to the bezel. 8. Install the rear door latch.


How do you remove exterior door handle 1961 VW Beetle?

There are 2 screws on the inside of the door under the door seal, remove and slide the door handle off.


To install a new door handle on a 92 Honda accord does the door panel need to be removed if one can still open the door without the handle?

yesAnswer: The interior handle? No.The panel does Not need to be removed to install a new handle. Look for a tiny round cap in the center of the handle. Remove it, and remove the Philips screw behind it. Push the handle bezel forward to unhook it from the door. Unplug the power window switch connector. Use a flat head screwdriver to carefully push the plastic clip off of the rod. The handle is now free.


Remove exterior door handle on 97 VW jetta gt?

How change door handle,drive side jetta 97


How do you remove exterior door handle on 1999 SL2 Saturn?

Lift up on the handle. You should see plastic inserts that fit into two tiny holes. Remove the inserts and the handle should slide to the side.


How do you replace a door handle on a 95 Toyota tercel?

You will need to remove the door panel of your 1995 Toyota. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.


How do you change a door handle on a Chevy truck?

You will need to remove the inside door panel of your Chevy truck. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.


Can recessed medicine cabinets be installed on an exterior wall?

Can but shouldn't. You would have to remove a lot of insulation to install it.


How do you change the exterior door handle on a 1998 Ford Explorer Sport?

Remove the door panel. Drill out the rivets in the exterior handle with a 1/4 drill. Carefully pull the handle out and disconnect the pull rod. Use small bolts and lock nuts to reattach.


How do you replace an outside door handle for a mustang?

You will need to remove the inside door panel of your Mustang. Remove the linkage from the outside door handle. Remove the outside door handle retaining bolts. Reverse the process to install the new outside door handle.


How do you remove the exterior door handle on a 1998 Mitsubishi Eclipse and install an aftermarket handle?

you have 2 take the inside door panel off & unscrew the two nutlike thinggy's and detatch the little spring and pull off from the outside instalation is the reverse of the former very easy fix!