Best Answer

You will need to remove the inside door panel of your 1988 Chevrolet Blazer S 10. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.

User Avatar

Wiki User

โˆ™ 2014-09-18 00:22:23
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace an exterior door handle on a 1988 Blazer S10?
Write your answer...

Related Questions

How do you repair an exterior door handle on a 1988 Chevy Monte Carlo?

Should be able to access after removing interior door panel


Are the door interchangeable on an 1987 chevy truck and an chevy blazer 1988

How do you replace the air compressor on a 1988 Chevy s-10 blazer?

There is no Air Compressor on a 1988 Chevy S-10 Blazer. I'm sure they meant the A/C compressor. And if you're not licensed to handle refrigerant you should take it to a mechanic that is since the lines will have to be disconnected to remove the old one and install a new one. Not to mention putting it under vacuum and recharging the system. The compressor is about $150 at Auto Zone, but removal and replacement rates vary.

Will a 1984 S10 blazer bumper fit a 1998 blazer?

no you need one off at least a 1988

Does a 1988 4.3 s10 blazer have a posi rearend?


Where is the fuel filter located on the 1991 s 10 blazer 2w drive?

where is the fuel filter on a 1988 s-10 blazer

What is the diameter of the heater hoses on a 1988 S10 blazer?


What kind of automatic transmission is in 1988 s10 blazer 4x4?


What is the tire size for A 1988 chev blazer from the factory?


What size engine in 1988 4x4 s10 blazer?

2.8 or 4.3

What are the speaker sizes in a 1988 Chevy Blazer s10?

The 1988 Chevrolet Blazer front speakers measure three inches by four inches. The rear speakers measure four inches by five inches.

How do you replace the alternator on a 1988 Pontiac fiero?

How do you replace the alternator on a 1988 Pontiac Fiero

What is the factory speaker size in a 1988 Blazer?

The full size blazer has 5.25 in the kick panel and 4 x 10's in the rear.

Location of the oil pump on a 1988 S10 blazer?

Inside of oil pan.

How do you adjust the choke on a 1988 Chevy s 10 blazer?

There is no choke to adjust.

Where is the solenoid starter on a 1988 Chevy s10 blazer?

It is mounted on the starter motor itself. When you get another starter, it will have the solenoid mounted on it already. If it is bad, just replace the starter, I would not change just the solenoid.

Will a 2.8 engine from a 1988 Chevy beretta fit a 1989 Chevy blazer?

Yes it will, but you have to put all the blazer engine stuff onto the beretta engine...

Where can you find a wiring diagram of the ignition system on a 1988 Chevy S10 Blazer?

1988 s10 blazer cruise control not working?

you may have a vacuum leak somewhere.

Strenghten the rearend of your 1988 S10 blazer?

As I don't own one there is no need to strengthen it.

What is the port for under the dash on 1988 S10 blazer?

That would be the OBD I Diagnostic Connector.

How do you set timing on a 1988 Chevy blazer s10 v6?

I have a 1987 Chevy Blazer S 10 4X4 2.8l V6 and the timing recommendation is 10 degrees.

How do you replace a broken throttle cable on a 1988 Ford Ranger?

how do i replace a throttle cable on a 1988 ford ranger pickup

Is the 1988 Blazer tailgate the same as the 1987 Suburban tailgate?

no, they are totally different sizes and profiles

Are the wheel lugs on a 1988 s10 blazer reverse threads?

No. Lefty=Loosey, Righty=Tighty.