0
How do you remove automatic transaxle drain plug 2004 hyundai santa fe 6 cylinder?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you change the transaxle fluid in a 2001 Daewoo Lanos automatic?
You have to remove the trans. pan.
How do you change a 1997 Chevy cavalier automatic transaxle fluid and filter?
Remove the transmission pan.
How do you replace the automatic transmission on a 1997 Hyundai Elantra?
1. Disconnect negative battery cable. Remove battery and battery tray 2. Remove the air intake duct and the air cleaner housing 3. Disconnect the transaxle ground cable and the transaxle range sensor 4. Disconnect the transaxle harness connector from the side of transaxle 5. Drain the transaxle fluid then disconnect the transaxle cooling lines 6. Remove the upper transaxle-to-engine mounting bolt 7. Raise the car and support it on jack stands. Secure the engine with a engine support brace or with an engine lift and chain. 8. Remove the transaxle mount bracket 9. Remove the front wheels 10. Remove the bolts from the center member and the transaxle roll stopper 11. Disconnect the lower control arms from the steering knuckle and remove drive axles 12. Remove the transaxle stay followed by the bell housing access cover 13. Remove the torque converter bolts. A screwdriver wedged in the ring gear teeth will keep the torque converter from rotating. Rotate the engine for access to all bolts 14. Support transaxle with transmission Jack to lower transaxle from car 15. Make final check everything is disconnected 16. Remove the mounting and retaining bolts and lower transaxle from the car
What size socket do you require to remove cylinder head bolts on a Hyundai coupe v6?
10mm
How do you replace a 2001 Hyundai sonata 6 cylinder alternator?
is there a quick way to remove alternator
How do you replace murry mower belt.rear engine?
Remove four bolts that hold transaxle remove belt pulley and belt guard. remove shift linkage remove spring tensioner. then remove whole transaxle. Remove four bolts that hold transaxle remove belt pulley and belt guard. remove shift linkage remove spring tensioner. then remove whole transaxle.
How do you locate the transmission fluid drain plug on a 1994 Buick lesabre?
If you have an automatic transaxle, there isn't a drain plug. You remove the fluid by removing the bottom pan on the transaxle, or taking it to a shop that has a vacuum pump to pump the fluid out through the fill hole.
How do you remove a 1997 Ford Escort transmission?
That depends on whether you have a manual 5 speed or an automatic. On both you have to support the engine from above since 2 of the 3 mounts are on the transmission. Disconnect all the electrical connections. Remove the bolts and nuts that hold the left hand engine mount. Remove the upper front and upper rear bolts that hold the trans. to the engine. Remove the starter motor. Remove the drive axles. Drain the transaxle fluid Remove the crossmember. Unbolt the gear shift rod from the input shaft of the transmission. Remove the nut that holds the gear shift bar to the transaxle. Then slide the bar off the stud. Remove the clutch slave cylinder. Remove the 2 lower bolts that hold the transaxle to the engine. Put a transmission jack under the transmission Remove the catalytic converter. With the transmission supported well, remove the last 3 bolts that hold the engine to the transmission. Carefully lower the transaxle and slide it from the engine.
How to remove ignition cylinder 2002 Hyundai?
The ignition cylinder on a 2002 Hyundai is a quick repair. First the lower steering column will need to be removed so the lock cylinder can be accessed. Once off, loosen the mounting screws for the cylinder. Insert the key and push the tab in while turn the key slightly so the cylinder can be unlocked from the housing.
What are the steps in pulling a 3-speed auto in a 1998 2.2 Pontiac Sunfire?
Disconnect the negative battery cable. Properly drain the transaxle. Remove the air intake duct. Disconnect the TV cable. Remove the shift cable and bracket. Tag and detach all necessary vacuum lines and electrical connections. Remove the power steering pump and set aside. Remove the transaxle filler tube. Install engine support fixture J 28467-A or equivalent. Remove the top engine-to-transaxle bolts. Raise and safely support the vehicle. Remove both front tire and wheel assemblies. Remove the left splash shield. Remove both front ABS wheel speed sensors and the harness from the left suspension support. remove both lower ball joints. Disconnect the stabilizer shaft links. Remove the front air deflector. Remove the left suspension support and both drive axles. Disconnect the engine-to-transaxle brace, then remove the transaxle converter cover. Remove the starter Unfasten the flywheel-to-torque converter bolts. Disconnect the transaxle cooler pipes. Detach the ground wires from the engine-to-transaxle bolt. Remove the cooler pipe brace and the exhaust brace. Remove the bolts from the engine and transaxle mount. Support the transaxle with a suitable jack. Unfasten the transaxle mount-to-body bolts. Remove the heater core hose pipe brace-to-transaxle nut and bolt. Unfasten the remaining engine-to-transaxle bolts, then remove the transaxle assembly from the vehicle.
How do you remove a rear transaxle mount on a 200 mercury villager?
Support the transaxle and unbolt it. You may have to remove some things to get clear access to it.
Replacing alternator 2004 Hyundai Sonata six cylinder?
My son has been trying to remove my 6-cylinder Hyundai Sonata for 4 hours. He just got it - you have to pull the motor mount and jack the engine. OR take it to your local mechanic and save yourself the hassle.
