answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: How do you remove oil cooler for Isuzu KB280?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace oil cooler lines on a 2001 2500 HD?

do you remove motor mount to remove oil cooler lines on 2001 chev 2500 hd 4x4


Where do you put the oil in a 1993 Isuzu Rodeo?

The oil in a 1993 Isuzu Rodeo is put into the reservoir that is located on top of the valve cover. There is a cap that has to be rotated to remove it.


How do you Remove Isuzu 4 x 4 trooper oil pan?

with an axe


How do you remove the engine oil cooler adapter from a 4.3 Chevy?

remove oil cooler lines from adapter held in place by 8mm bolt, if you remove the oil filter you will see 2 torx bit bolts they are t40 bit, undo all of that and its removed


How do you remove the oil cooler from a 2000 Chrysler Concorde lxi?

you have to remove the radiator,the cooler is integral to the rad,so the entire rad must be replacedh


How do you remove the engine oil cooler adapter from a 91 350 and reinstall filter without adapter?

I assume you are working on a 350 Chevrolet small block with the factory GM oil to water cooler in the radiator? Why remove the oil cooler? With the engine cold, remove the oil filter from the adapter. Remove the lines from the remote cooler adaptor first. Then look up into the cavity (above where the oil filter screws on) and you will see two bolts. Remove these two bolts and the adaptor will come off. Obtain a regular GM (Chevrolet small block) oil filter adaptor from any non-oil cooler application with the bolts. There are a million places to get these. Bolt the new adaptor in place, screw on a new oil filter and off you go. The factory filter seals against the flat surface of the engine block and the filter now screws onto the oil filter adaptor instead of the cooler adaptor. You may want to remove the oil lines to the radiator and plug the oil cooler openings in the radiator. If the oil cooler is already or begins to leak you will loose coolant through the cooler openings. mlynch003@yahoo.com


Where is the oil pressure sending unit on a 2000 Isuzu Rodeo 3.2L V6?

It is on the oil cooler manifold, next to the oil pressure switch.look front of engine below harmonic balancer,before oil filter.


How do you take oil cooler off on a ford 7.3 liter 2001?

how to take an oil cooler off a 7.3 liter ford 350 Drain the coolant remove the oil filter. Remove two 10mm head bolts from the front of the cooler and the other 4 which are located by the oil filter. You can then slide the entire cooler out the back and that's it. Model years prior to 99 you do the same thing but have to loosen the left motor mount to be able to remove the cooler. 99-2003 it slides right out. Good luck.


How do you change oil cooler lines on 1996 Chev Tahoe?

Remove the old oil filter. Drain the oil and remove air cleaner housing. Place the car on Êa jack. Loosen the engine mounts. Raise the engine and loose the bolts on the motor mounts. Remove the engine shock and the two brackets securingÊthe oil lines. Remove the oil cooler lines.


How do you remove the oil cooler from under the oil filter on a 95 Camry with a 2.2?

get a big "f-n"hammer


How many quarts of oil go in a GMC Engine 455 Motorhome?

Your engine will take 6 quarts of oil ,,,unless it has the optional external oil cooler,,then you will have to know the capacity of the cooler. Be careful when putting oil in--it's always easier to remove excess oil than remove a damaged engine due to lack of oil.


How do you remove oil cooler lines from the oil filter housing?

Their should only be two bolts holding it in. If you want to remove the oil cooler lines and thus not use the oil cooler system at all you must do the following and not put plugs into the inlet and outlet ports. Diconnected the two oil lines, remove the oil filter adapter. Install the proper oil pressure regulator ( a dealer part) onto the block where the oil filter swrews on. If you only plug the ports in the original oil cooler adapter you will starve the engine of oil pressure since the oil flow will be blocked off. Required adapter GM #3952301 and the gasket GM #31028280.