0
How do you remove passenger side steering knuckle from a 98 Audi A4 quattro?
Wiki User
∙ 15y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace front spindle on a 1997 ford escort?
It doesn't have a spindle. It has a steering knuckle and hub. To remove it: 1. Remove the hubcap and loosen the driveaxle retaining nut. 2. Remove the wheel and the driveaxle nut. Tap the end of the driveaxle with a hammer and a brass drift to loosen the splines in the hub. 3. Remove the brake calilper and support it with a piece of wire. 4. Separate the tie rod from the steering knuckle arm. 5. Unbolt the strut from the steering knuckle. 6. Remove the clamp bolt and the nut and detatch the ball joint from the steering knuckle. 7. Pull the hub and the steering knuckle off the drive axle.
How do you change the right front axle on a 1993 Dodge Spirit 6cyl?
while the car is on the ground, and the brake on, remove the bolt that keeps the axle on the steering knuckle... then raise the vehicle, and support the vehicle on jack stands, remove the tire then remove the ball joint clamp bolt... remove the 4 bolts going to the sway bar... use a pry bar and gently pry the control arm down... remove the bolt from the steering knuckle. pull the steering knuckle outward releasing the axle from the steering knuckle, then gently remove it from the transmission being careful not to damage the boot or the CV joint... to install just do it in reverse
How do you install the wheel bearings on a 1992 Lexus es 300?
remove the steering knuckle from the car and press, hub out of the knuckle. then remove snap ring and press out bearing you need a strong shop press
Do you need to separate the steering knuckle in order to remove brake rotor on a 1997 Honda Accord?
no, remove the caliper and the caliper mountaing bracket, if it is on the front you may have to remove the axle not but there is no need to remove any steering part
How do you remove the steering column in a Chevelle?
Unplug the wiring harness from the steering column. Remove the cover plate under the column. Remove shift linkage. Remove two bolts under the dash that hold the column up. Remove the two nuts that connect the column to the steering knuckle. Slide it out.
What is the special tool to remove front bearings on a 98 Honda civic?
They are pressed into steering knuckle. Remove steering knuckle from car, then you can put rounded end of ball pein hammer (make sure ball pein hammer end is big enough) into the opening where axle goes and hit it out by striking flat end of ball pein hammer with small sledge hammer. Ensure steering knuckle is solidly secured before striking with hammer.
Replacing alternator on a mercury mariner?
First,disconnect the battery.Remove tire.Set jack stands on frame not control arm you will be removing the steering knuckle for this job.Remove inner fender well.Remove brake caliper,brake caliper mounting bracket,rotor,remove lower balljoint nut,remove knuckle to strut bolts,remove abs sensor from knuckle,seep rate knuckle from lower balljoint
How do you take out a steering column on a 1977 Chevy pickup?
Unplug the wiring harness from the steering column. Remove the cover plate under the column. Remove shift linkage. Remove two bolts under the dash that hold the column up. Remove the two nuts that connect the column to the steering knuckle. Slide it out.
How do you replace front wheel bearing on 96 Ford Probe?
remove the wheel. support the control arm with a jack stand. remove the driveshaft/cvjoint nut (the big nut in the center). may need to have someone pressing the brake or at least losen before you jack it up and remove the tire. remove the brake caliper assemby and the rotor. remove the tie rod end from the hub/steering knuckle. remove the two nuts and bolts attaching the hub/steering knuckle to the strut/shock and the nut and bolt holding the the hub/steering knuckle to the lower ball joint. lift the hub off the lower ball joint slide the hub/steering knuckle off of the cv joint/driveshaft. there may be sensors for antilock brakes and such that need removed but it should be fairly obvious on how to remove just by looking at them. with the hub/steering knuckle out, the bearing is a sealed bearing and is pressed out of the center after removing a seal and the new one is pressed in. since i don't own a press, i would usually take it to napa autoparts or someplace that has a machine shop and have them press the new one in for me. then reassemble.
How do you remove hub and bearing on 2000 Nissan sentra?
remove the steering knuckle, put it in a vise and if there are no snap rings inside the axle opening, get a big hammer and go at it.
How do you remove the front wheel hub and bearing from a 1989 Ford Tempo FWD?
you need to remove the entire steering knuckle and have a machine shop press out the hub and bearing for you.
Are there any special tricks to replacing the passenger side CV shaft on a 2000 Blazer?
Loosen passenger side lug nuts. Raise and safely support front of vehicle with jack stands. Remove wheel. Remove axle hub nut and washer. To release inner CV joint from differential, hit the inner part of the CV tri-pot housing with a hammer and a piece of wood until the snap ring releases. Support lower control arm with a floor jack. Remove brake caliper and hang it out of the way with a piece of wire. Remove brake rotor. Disconnect tie rod end from steering knuckle. Separate and detach lower and upper ball joints from knuckle. Using a puller, push the drive axle out of the hub. Remove steering knuckle. Remove axle assembly. Torque front axle hub nut to 103 ft lbs during assembly.
