0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you remove the rotor to access the ignition coil for the Honda Civic?
a little 8 mill screw on bottom of rotor into dist shaft
How do you remove cap and rotor on 1992 Honda Civic 1.6 engine?
Loosen the screws on the cap and there is a single screw holding the rotor to the shaft
How do you remove the front rotor on 1999 RX300?
Remove the brake caliper and hang it out of the way, then thread 2 8 mm bolts into the holes provided on the disk. Screw them in and the brake rotor will come off.
How can you remove stuck brake rotors on a 1987 Pontiac Bonneville?
Remove set screw. Then tap the rotor with a hammer. The rotor should break free. It has just rusted itself to the axle, due to condensation.
How do you charge the condenser for a non HEI ignition on a 1970 Chevy 350?
If you're asking how to change the condenser, it is under the rotor. Remove cap and rotor, remove condenser wire from contact set (either held in place with a screw or spring tension), remove the screw that holds the condenser bracket ( magnet or screw starter is very helpful), then reverse procedure to install new condenser.
How do you take a rotor off a 1999 Daewoo is it the center nut or the screw on the rotor?
The center nut is for the hub assembly. You need to remove the screws on the rotor. The screws might be stuck to the rotor when you try to take it out. If this is the case, be careful when you use the screwdriver. You might round out the screw head. When the screw is hard to remove, I usually use a 1/4" socket wrench, 1/4" socket, and screwdriver bit. The screwdriver bit will fit inside the 1/4" socket. This gives you extra torque and won't round out the screw as a screwdriver might do. Once the screws are out, the rotor should come right off.
How to Remove rotor on mini cooper?
You'll first need to remove the brake calipers. Once they are removed, there's a screw you'll need to remove from the center section of the rotors between the lugs. More than likely, the screw will be frozen and hard to remove....likewise, once it's removed the rotor itself will probably need coaxed off as well. Tap around the rotor edges with a rubber mallet until it comes free.
How do you remove the distributor rotor on a 1989 Isuzu amigo?
There are 3 screws holding the distributor cap on. After removing the cap, there is a small Phillips head set screw holding the rotor in place on the shaft portion of the rotor.
How to remove rear brake rotor on 1999 Chevy blazer?
If they are rotors then you will take the caliper off of the bracket via 2 bolts usually then remove the bracket from the spindle via 2 bolts and the rotor should come right off. However some vehicles have a screw on the bolt hole face of the rotor and if you have one you'll need to remove it. It's usually a Phillips, just get a screw driver large enough to fit it and use a hammer to tap the end of the screw driver to loosen it up. With a hammer hit the non rotor surface around the inner circumference, then tap the rotor from the back access hole. Spraying the "hub" where it contacts the rotor with WD40 will help to loosen the rotor up as well. Hope this helps good luck!
How do you remove rear brake rotor on xg350?
1st remove the tire, than remove the brake caliper there are two bolts that are in the back side of the caliper slide the caliper unit off the rotor. on the front of the rotor there is a Phillips set screw next to one of the lug nuts remove it than tap the rotor. You may need to spray some lubricant to loosen any rust or build up. Than replace.
How do you remove the distributor rotor set screw on a 1997 Honda Accord SE four cylinder not VTEC with the plastic cover under the rotor blocking access?
In order to get the set screw in a position so it can be easily removed, you have to get the rotor to rotate. Act as if you are going to start the car, but only hold the key in the start position for a split second. The cars engin will turn over, and the rotor will rotate, hopefully to where it is easier to get the screw out. If not, try again.
How do you change a rotor on a 2002 Jetta?
take the wheel off, remove the two bolts off the back of the caliper, take the caliper off the rotor, take the little star screw out of the the face of the rotor, after that take a mallet and tap the rotor and it should come right off!
