0
What else can I help you with?
How do you replace brake disc on a 2000 Pontiac sunfire?
Lift car, remove wheel, remove caliper & caliper bracket (bolts in back near strut). Give the rotor a wack with a hammer if it's stuck on the hub and remove it. Reverse to install.
How you replace odometer bulb on a 98 Sunfire?
You have to remove the dashboard, then remove the instrument cluster. On the back of the cluster, you'll find that you can unscrew the bulbs from the back and replace them. I've done it myself on my own 99 Sunfire --- CanadianCynosure
How do you remove the brake pads only ON A 2001 ALERO?
there should be 2 bolts which hold the brake caliper on the rotor u will need to remove them to remove the caliper then just use a screwdriver to pop the pads off the caliper u will also need a C clamp to compress the piston back in the caliper or u will not be able the replace the caliper on the rotor
How do you remove the front brake rotor on a 1999 Plymouth Voyager?
Remove tire. Remove Caliper and pads The Rotor will just slip right off the spindle... Put new rotor on, put caliper plus pads back and the tire and your done, its really simple to do.
Where is the crankshaft position sensor located on a 2001 Pontiac sunfire?
on the back of the motor wright below the crank sensor
Rotor removal on 82 Camero?
Remove the wheel. Unbolt and set aside the brake caliper. Remove the dust cap at the center of the rotor. Remove the cotter pin, then unscrew the wheel bearing nut. Wiggle the rotor a bit, then remove the outer seal (washer) and outer wheel bearing. Put the nut back on a few turns Grasp the rotor very gently and slide the rotor off at high speed allowing it to drop by force of gravity. The inner bearing should snag on the nut keeping the inner bearing and race on the spindle as the rotor comes off. Remove the nut. Do not forget to clean and repack your wheel bearings before you put the rotor back on.
How do you remove rotor from 2004 ford f-250 four wheel drive?
front or rear rotor? jack up wheel that needs rotor removed. remove wheel remove brake pads and caliper for back axle, remove axle nut. u will need special socket to remove this nut slide rotor off axle, making sure u dont drop bearings on the ground to remove front rotor on4x4, it is pretty much the same as rear , except you will have to remove locking hub from axle before you can remove axle nut.
How do you remove a front rotor on a 1976 Chevy Malibu Classic?
Remove spindle cap, cotter pin, spindle nut, outer bearing. Now you can pull off the rotor which has another bearing on the back and a seal.
When you are top dead center your rotor points to the number seven cylinder how can that be repaired?
You must remove the distributor and rotate it back until the rotor is pointing at #1 when you set it back down in the block. It is trickey to do.
How do you replace front rotors on a 2000 Nissan Frontier?
You have to take off the cap in the middle of the rotor...which houses the bearing, then unscrew two screws and remove the retainer ring( be careful not to strip the screws), then use a screwdriver and a hammer to remove the nut that holds the bearing in pull on the rotor till it comes off...then use a 14mm socket or nut driver to remove the rotor from the mounting hub.....pop the ring off holding the back bearing then put the bearing in the new rotor then put the ring back on....then bolt you mounting hub back on and slide the rotor back on the spindle....make sure it goes on all the way...
How does one remove a front brake rotor on a 2001 Mazda B3000 pickup 2 wheel drive because you can't get the rotor by the caliper holder?
there are 2 bolts on the back side of the caliper holder that you need to take out and the hold will come off, then pull the caliper off if it doesn't come off hit the rotor with a hammer until it comes off
How do you remove rear brake rotor on xg350?
1st remove the tire, than remove the brake caliper there are two bolts that are in the back side of the caliper slide the caliper unit off the rotor. on the front of the rotor there is a Phillips set screw next to one of the lug nuts remove it than tap the rotor. You may need to spray some lubricant to loosen any rust or build up. Than replace.
