IT IS MOUNTED BY RIVETS. YOU MUST DRILL THEM OUT
To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them.
Begin by removing the inside door panel. Remove the wiring harness from the electric window regulator. Remove the window regulator retaining screws.
Disconnect the battery.Remove the door panelRemove the power window motorRemove the regulator spring.Move the window down a bit and remove the two 10MM nuts from the window.Twist the window spring stud counter-clockwise.Now you should be able to remove the window regulator.
To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.
need to know how cables connect on window regulator
Remove the 1997 Chevrolet Suburban drivers side door panel. The window mechanism will be visible. Place the new window into the window track. Secure the window to the track.
Remove the door panel. Remove the bolt that fastens the regulator to the window. Remove the 3 bolts that hold the regulator assembly to the door. Squeeze the entire assembly through the largest hole and replace with a new assembly in reverse order.
Remove the window regulator assembly from the door.Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.Connect the window motor to the regulator with 3/16 in. rivets.Install the window regulator assembly.
First you need to remove the door panel.Then remove the door handle bracket.Peel back the moisture shield.Tape the window into place,then unbolt the window from the regulator.Remove the window regulator from the access hole in the door.
1 open door 2 remove inner panel 3 lower window 4 take out window 5 remove (4) screws from regulator 6 take regulator of rails
It is best to replace entire regulator as one unit. Remove door panel. Remove bottom nut of regulator, and remove two top nuts of regulator. Loosen two bolts on bracket holding window. Support window, and carefully remove regulator as one unit.
remove your door panel there will be three screws holding it on. then you have to remove the screws holding your window to the regulator. then unbolt regulator and motor from door. Undo wiring going to motor.
Lower window at least a couple of inches if possible. Remove interior door trim panel. Unplug anything at trim panel. Unplug window motor. Remove 2 bolts holding glass to regulator. Tilt window glass forward, then remove upward and outward from door. Remove 4 or seven bolts and/or nuts mounting regulator and motor to door frame. I think it's 4. Maneuver regulator out of door frame. If 4 in above step, remove 3 bolts mounting motor to regulator, otherwise you'll be replacing the whole regulator. Install by reversing above procedure.
Anyway, the part# from napaonline.com is BK 6653601 for the drivers side (BK 6653602 for the passenger side). Remove the door panel, time consuming but not too hard. Loosen the three 10mm bolts holding the motor in, remove the power connector. Lower the window so that the two bolts holding it to the regulator are exposed, remove them. Push the window to the top, propping it at this position (a screwdriver through the access hole at the top left will prop on top of the exterior door handle keeping the window in place. Remove the three 10mm bolts holding the regulator in place. 'Corkscrew' the regulator and motor out of the BIG hole at the back of the door. Installation is the reverse of assembly. EASY!
u have to remove the drivers window and remove the regulator assy...once its out there ar 4 rivits u have to drill out be very carefull of th spring in the regulator it will come out and injure u if u don't take the proper precautions
How to remove the window motor from the regulator
You will need to remove the door panel and see if the motor and/or the regulator is bad.
The window is not off track. The window regulator is broken. In most cases you will have to replace the window motor and regulator as an assembly.
replace window regulator
First remove the door panel.Then remove the moisture barrier.Next remove the window motor from the window regulator.
remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.
You will have to replace the complete window regulator assembly.
Remove the inside door panel of your 1994 Chevrolet Corsica. Remove the window motor wiring harness. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.
To remove the rear window regulator on a 1994 town car, remove the screws under the arm rest. Take off the rubber insulation and unplug the speaker wires to get it our of the way. Finally, remove the window regulator.Ê
The panel where the regulator is detachable. You will be able to remove it very easily. When you remove the panel you will see the way how the regulator can be replaced.