Door Panels and Handles
Chevy Malibu

How do you remove the driver door panel on a 2002 Chevy Malibu?


Top Answer
User Avatar
Wiki User
2014-10-06 22:16:17
2014-10-06 22:16:17

Using a screw driver, remove the screws and the clips in the panel of the door and remove the panel gently. Remove any wiring connectors between the panel and the door, then remove the panel the rest of the way.


Related Questions

what steps are required to remove the inside door panel on a 1997 Chevy Malibu.

open the driver side door. There is a panel on the dashboard that is really easy to remove when the door is open... ope panel, see fuses and on the panel is a diagram to locate which is which!

Here's a great how to video that will show you how to properly remove the door panel on your 2005 Chevy Malibu. A link has been included below.

Depending on what panel your are talking about, but the panel around the radio just "pops" off. Well actually they both just pop off but you may need to assist them with a small flat-headed screw driver.

Using a screw driver remove the screws from the door panel, remove the clips, and pull the panel away from the frame slowly. Remove any wiring connectors, and remove the panel the rest of the way.

Using a screwdriver, remove the screws that are in the door panel, be sure to remove the clips as well, and gently pull the panel away from the frame. Remove any wire connectors between the frame and the panel, and pull the panel off the rest of the way.

You must remove those pieces that don't seem to flow with the door panel (they pop right off with a screw driver), then you will se screws underneath them... unscrew these screws and the door panel should easily pop right off.

you have to remove the driver seat belt and remove the panel it is behind there

The speaker cover's you are referring to, are they in the front or back of the vehicle. If in the front you have to remove the door panel. If in the back, just grabe yourself a flat head screw driver and carefully push under cover and pop out.

Open driver or passenger door and remove interior panel for fuses. Should be located in the fuse panel

the horns are located on the passenger side under headlight in the fender. remove the plastic panel to access them. you may have to remove wheel also.

how do you take the dash board outon a 2006 chev Malibu

Remove the screws in the door panel.

Unless there is an access panel in the trunk you will have to remove the fuel tank. I would check with your Chevy dealer, as this may still be under warranty.

Take the door panel off and there are bolts inside.

Open the driver door and remove the panel on the end of the dash

The 1985 Chevy Caprice driver side door panel is held in place with for retaining bolts and 10 retaining clips. Remove the retaining bolts. Pry outward on each retaining clip. The door panel will come off.

The 2005 Chevrolet Malibu OBD 2 port is under driver side next to kick panel

Remove the driver of it in the the Control Panel-Devices And Printer-Right Click On the REMOVE DRIVER From iT Your Problem Is Solved

The 1993 Chevy Caprice Classic drivers side door panel is held in place with for retaining bolts and 10 retaining clips. Remove the retaining bolts and pry outward on each retaining clip.

Remove the inside door panel from your 1991 Chevrolet 1500 pickup truck. Remove the wiring harness from the mirror. Remove the driver side mirror retaining bolts. Reverse the process to install the new driver side mirror.

pop out small panel behind door pull remove two torx screws , remove two pop out connectors on outer edge of door panel near door latch ,grab bottom of door panel and pull it towards you this will release panel ,disconnect wires as needed if you want to remove entire panel from door, lift up on panel to remove it from edge of window track

Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.